An exclamation point "!" is displayed on the DAQ32Plus hard disk icon.

(ns-faq-daqworx-13052-spec)

The exclamation point is displayed when data cannot be written to the hard disk. Check whether the save destination folder exists, and whether there is sufficient free space on the disk.

The DA100 and DAQ32Plus are connected, but I can't record.

(ns-faq-daqworx-13051-connect)

If you have not changed any settings, check the following. Check the amount of free space on the hard disk, and perform error checking Check the DA100 power, and whether the green STATUS lamp is lit Communication cable connection and replacement...

How can I perform strain initial balancing on DAQ32Plus?

(ns-faq-daqworx-13050-spec)

Upload settings as follows: Darwin setting icon > Communication > Receive. Next, select Communication > Execute > Balance. Select Balance for the execute type, then select the range of channels and execute the balancing. (Setting the exec...

Can I automatically convert measured data files to Excel on DAQ32Plus?

(ns-faq-daqworx-13053-spec)

Yes, with the auto processor.

I want to set an IP address on the DA100 Ethernet module by using DAQ32Plus. When I place the dip switches in Config mode and press "Check," error E3339 appears. How should I enter settings? My PC uses Windows 7, with the latest version of DAQ32Plus.

(ns-faq-daqworx-13064-connect)

Since the OS security level has increased, you can no longer set the Ethernet module's IP address on Windows 7. Data acquisition will be unaffected, but for the IP address setting use a Windows XP PC with DAQ32 installed.

How can I view historical data files (*.daq) and reports (*.rbi) from DAQ32 and DAQ32Plus on a Windows 10 PC?

(ns-faq-daqworx-13078-spec)

Use the latest version of SMARTDAC+ Standard Universal Viewer.

Can DAQ32 monitor 30 channels worth of data?

(ns-faq-darwin-8023-spec)

It can monitor up to 20 channels. If you need more channels, please consider DAQ32Plus (supports up to 300 channels).

How many data can be displayed along the time axis in DAQ32Plus' real time trend display?

(ns-faq-daqworx-13049-spec)

Up to 1800.

When purchasing a DAQ32Plus upgrade license (WX102UP), what sort of license number is required?

(ns-faq-daqworx-13065-other)

It is a number starting with 101, and is included in your DAQ32Plus CD case. If you lose the license number, order model no. WX102.

I set the same IP address on the DR241 and PC to connect via Ethernet, but there's no communication.

(ns-faq-daqworx-13039-connect)

Communication cannot open if the IP address is the same.

Can I monitor and record on two DA100s using DAQ32Plus?

(ns-faq-daqworx-13038-spec)

No. DAQ32Plus only supports 1 unit. We recommend using DAQLOGGER.

When assigning DAQ32Plus groups, can I arbitrarily sort channels independently of the sorting on the DA100? Also, can I register channels to multiple groups?

(ns-faq-daqworx-13048-spec)

Yes.

What communication formats are compatible with DAQ32Plus?

(ns-faq-daqworx-13040-connect)

Ethernet, RS-232C, RS-422A/485, and GPIB.

I've set the host name and port number on the DAQ32Plus client, but am unable to connect.

(ns-faq-daqworx-13043-connect)

Launch the DAQ32Plus monitor, then start the client.

How many groups, and how many channels per group can be displayed in the DAQ32Plus real time trend screen? Also, can I set the display span on the DAQ32Plus side only?

(ns-faq-daqworx-13047-spec)

Up to 30 groups of up to 32 channels each can be created. You can set the display span in the detailed display settings.

Can I view DAQ32Plus real time trends on multiple PCs?

(ns-faq-daqworx-13046-spec)

Yes, by using the DAQ32Plus client package. The latest version supports monitoring of 1 DAQ32Plus monitor server by up to 16 clients.

I'm using DAQ32Plus. I set an alarm on the DARWIN (DC100). When the measured value rises, an alarm appears in the DARWIN (DC100) screen, but in the DAQ32Plus screen the alarm stays green (doesn't turn red).

(ns-faq-daqworx-13067-soft)

Check whether "Alarm data" is checked in the DAQ32Plus Logger acquisition conditions. If not, the alarm on the DAQ32Plus screen remains green and doesn't turn red even if an alarm is reported on the DARWIN hardware.

When I acquire DI input with the BFD32 and perform statistical computation (averaging) on the Viewer software, I get computation errors 0 and 1.

(ns-faq-darwin-8004-spec)

The Viewer cannot determine the numbers after the decimal with statistical computation on DI input. Data acquired and results computed by the BFD32 are affected by the decimal of the specified measurement range. For DI (contact input), a 4.2 µA...

When connecting the DA100 and monitoring trends, the PC's time differs from the time displayed in the trends.

(ns-faq-daqworx-13045-spec)

The time in the trends is the time on the DA100. When connected for a long time, the times on the PC and DA100 can start to diverge. Closing and then reopening the connection will synchronize the times because the PC's time is automatically set o...

DAQ32Plus can't communicate with the DA100 via Ethernet.

(ns-faq-daqworx-13042-connect)

Double-click the DAQ32Plus environment settings icon, click the Environment tab, and make sure ETHERNET is selected and that the DA100's IP address is set. If the IP address is not set, set it and then restart DAQ32Plus.

When I connect the DA100 via RS-232-C and use DAQ32 Plus to acquire data, the performance bar goes to OVER and I lose data. What should I do?

(ns-faq-darwin-8027-spec)

Because DAQ32 Plus has greater functionality than DAQ32, it requires that much more CPU speed and memory. If there was no problem on DAQ32 but the performance bar goes to OVER on DAQ32 Plus, probably the baud rate set on DAQ32 is too slow for DAQ32 P...

Can I forcibly turn the alarm output modules ON/OFF from a PC regardless of any input data alarms?

(ns-faq-darwin-8055-spec)

You can, starting with style 8 of the DA. Setting command: VS. Control execute command: VD. The DR and DC do not support this. With DAQ32 and DAQ32Plus you can set up output relays, but you can't actually operate them with commands. You can also ...

When I add a module and configure the system, are the settings initialized?

(ns-faq-darwin-8058-spec)

Generally they are not initialized if the modules are not different from the previous system. However, initialization happens if slots are in the following conditions. Slot replaced with a module of a different model name or style number Slot who...

I’m trying communication from a RS232C communication module (DT300-31) to a recorder using DAQ32 software, but *E0401 Communication error* is displayed and communication fails.

(ns-faq-darwin-8068-connect)

On the RS232C communication module, set communication parameters by using the dip switches on the front of the module. Make sure the communication module’s dip switches match what is displayed on the DAQ32's “Environment, diagnosis, a...

What is the temperature measurement interval of the universal module's RJC (INT)?

(ns-faq-darwin-8051-spec)

For 0.5 second models, temperature is measured for RJC every 2.5 seconds (with a 0.5 second scan, since the time for processing temperature measurement, burnout, and other factors is too short, measurement occurs every 5 cycles). For 2.0 second mode...

When measuring voltage with a universal input module or DCV/TC input module, what is the limit value where an overrange occurs?

(ns-faq-darwin-8029-spec)

For voltage measurement, if 5% of range + range span is exceeded, an overrange occurs (±32767 is output). For temperature range, the +10°C measuring range is the upper limit. Ex) For the ±50 V range (span of -50 to +50), the upper l...

Does DARWIN support Windows XP?

(ns-faq-darwin-8017-spec)

R10.03 and later support Windows XP.

When I changed to Windows 7, I couldn't change the IP address of the Darwin Ethernet module. What should I do?

(ns-faq-darwin-8018-setting)

DAQ32 (DP120) or DAQWORX DAQ32 Plus (WX102) installed on Windows 7 or Windows Vista cannot change the IP address of DARWIN series Ethernet modules (suffix code /C7) or DARWIN series standalone models with the Ethernet communications option (model cod...

Can I connect the main unit to a company network?

(ns-faq-darwin-8019-connect)

Yes. Set the IP address, subnet mask, and default gateway on the main unit.

What internal processing occurs of the DI input (non-voltage contact input) from the universal input module and DCV/TC/DI modules?

(ns-faq-darwin-8050-spec)

The voltage generated when a burnout current of 4.2 mA flows to the measuring terminal circuit is measured in the 60 mV range, and a determination is made. If 42 mV (10 kΩ) or more, the result is 0 (open). If less than that, 1 (closed).

DP321 (INTERRUMPIDO)

Resources