Field Wireless Media Converter YFGW610 is used for signal conversion between Field Wireless Management Station YFGW410 and Field Wireless Access Point YFGW520.
- Special Design for Field Wireless System:
Low latency and high quality network can be configured, corresponding to high precision time synchronization specified in ISA 100.11a standard. - High tolerance to harsh environment:
Wide range of operating temperature and surge protection ensures safety and high reliability of Field Wireless System. - Reduction of Installation Cost:
Installation can be simplified by plug-and-replay function, which is unnecessary to configure itself.
Details
Field Wireless Backbone Specifications
| Communication Interface | Standard | 100BASE-TX1 |
|---|---|---|
| Transmission Speed | 100Mbps | |
| Connector | RJ-45 | |
| Cable Type | Category 5 | |
| Center Wavelength | － | |
| Maximum Length | 100m | |
| Number of Ports | 4 ports | |
| Port Name | B1, B2, B3, B4 | |
| Protection | Surge | |
| Port Connection | B1-1, B2-2, B3-3, B4-4 (fixed) |
- Connect to YFGW410
Optical Cable Network Specifications
| Communication Interface | Standard | 100BASE-FX2 |
|---|---|---|
| Transmission Speed | 100Mbps | |
| Connector | SC connector [1pole x 2] | |
| Cable Type | Multi-Mode Fiber*3 Single mode Fiber*4 | |
| Center Wavelength | 1300nm | |
| Maximum Length | 2000m(Multi-Mode) 5000m(Single Mode) | |
| Number of Ports | 4 ports | |
| Port Name | 1, 2, 3, 4 | |
| Protection | － | |
| Port Connection | B1-1, B2-2, B3-3, B4-4 (fixed) |
2. Connect to YFGW520. In outdoor wiring, it is recommended to use optical fiber cables with a nonmetallic tension member.
3. Core diameter / cladding diameter 50/125 μm core or 62.5 / 125 μm can be used.
4. ITU-T G.652 compliant products can be used
Installation Environment
| Functional specifications | Temperature Range | Op-40 to +65°C (altitude : up to 3000m) Storage: -40 to +85°C |
|---|---|---|
| Humidity Range | Operating: 5 to 95 %RH (non-condensation) Storage: 5 to 95 %RH (non-condensation) |
|
| Temperature gradient | Operating: ±10°C/h or less Storage: ±20°C/h or less |
|
| Power Supply | Voltage Range : 10.8～26.4 V DC Rated Power Supply : 24 V DC Momentary Power Failure : Instant Disconnection DC Power Supply Ripple Ratio : 1%p-p or less |
|
| Power Consumption | Max. 10 W | |
| Degrees of Protection | IP20 | |
| Vibration resistance | 0.15 mm P-P (5~58 Hz), 1 G (58~150 Hz) | |
| Shock resistance | 15 G 11 ms | |
| Noise resistance | Electric field : 3 V/m or less (80MHz~1GHz) Electrostatic discharges: 4 kV or less (contact discharge), 8 kV or less (aerial discharge) |
|
| Grounding | Class-D grounding (no sharing ground with others) | |
| Cooling | Natural Air Cooling | |
| Regulatory Compliance Statements | CE Conformity | EMC: EN61326-1 Class A, Table 2, EN55011 Class A group1, EN61000-6-2 |
| Safety Requirements | CSA C22.2 No. 61010-1 (Indoor use only) | |
| Explosion-Proof Types | ATEX Type n declaration |
Zasoby
Wireless technology has a long history, and it began around the time that James C. Maxwell theoretically predicted and then proved the existence of electromagnetic waves in the 1860s, and when Heinrich R. Hertz experimentally confirmed the actual existence of the electromagnetic wave in 1888.
In plant sites, there are various places such as those affording an unobstructed view like tank yards, and others surrounded by metal pipes and equipment obstructing the view (hereafter referred to "pipe jungles"), often seen in oil refinery and chemical on-site plants. The frequency band of radio waves used for field wireless communication is 2.4 GHz, which has high straightness and its ability to go around things can hardly be expected.
The introduction of wireless technologies into plants is anticipated as one of the measures for implementing field digital solutions not only to reduce cable wiring costs but also to improve plant wide safety/stable operations, operating efficiency, and so on.
The FieldMate versatile device management wizard is PC software mainly used for configuring and adjusting field devices. Under the concept of "one tool for all," Yokogawa has been enhancing this software to support a wide range of field devices and field communication protocols.
Downloads
Broszury
- Field Wireless Product Profile (479 KB)
- Yokogawa Field Wireless Solution (3.4 MB)
- SIL2 Wireless Gas Detection System (1.6 MB)
Instrukcje obsługi
Ogólne specyfikacje
- Field Wireless System Overview (1.9 MB)
- YFGW610 Field Wireless Media Converter (1.1 MB)
Schematy
Szukasz dodatkowych informacji na temat naszych pracowników, technologii i rozwiązań?
Kontakt