Name: JUXTA VJ 시리즈 신호 변환기
Brand: Yokogawa
SKU: juxta-vj-series-signal-conditioners

VJ 시리즈는 소형의 플러그인 형태로 다양한 애플리케이션을 수용 할 수 있으며 고사양형은 마이크로 컴퓨터 탑재의 고성능을 자랑합니다. 제 2 출력, 아날로그 출력, 상한 / 하한 경보 릴레이 출력 및 RS-485 MODBUS 통신을 설정할 수 있습니다.

공간 절약 대응 설계로 소형
외형 크기 : 높이 76 × 폭 29.5 × 안길이 124.5 mm
범용 입력 (VJU7)
온도 변환기 VJU7 입력으로 열전대, 측온 저항체 또는 mV 신호를 설정
절연 2 출력
옵션으로 제 2 절연 전류 또는 전압 (펄스)를 출력
• 통신 기능 (VJU7, VJH7, VJA7, VJQ7, VJQ8, VJS7)
옵션 RS-485 MODBUS 통신은 아날로그 출력 신호와 병행하여 사용 가능
경보 출력 (VJU7, VJH7, VJA7, VJQ7, VJQ8, VJS7)
옵션의 상한 / 하한 경보 릴레이 출력은 아날로그 (펄스) 출력 신호와 병행하여 출력 가능
HART 통신 신호 중계 기능 (VJA1 / H)
HART 통신 기능을 가진 필드 기기 및 DCS 사이에서 HART 통신 가능 (입출력 간 절연)
현장 설정
PC (파라미터 설정 도구 VJ77 소프트웨어) 또는 핸디 터미널 (JHT200)이 있으면, 마이크로 컴퓨터 탑재 형 VJ를 현장에서 구성 가능
Power supply voltage is either 100 to 240 V AC or 15 to 30 V DC
전원 전압 : 교류 100 ~ 240V 또는 직류 15 ~ 30V
3 년 보증
해외 안전 규격 (CE, UL, CSA)에 대응 ※ 일부 기종 만

Mounting and Appearance

Construction	Compact plug-in type (Main unit with Socket)
Mounting Method:	Wall, DIN rail, or dedicated VJ mounting base mountings
Connection Method:	M3 screw terminal
External Dimension:	Converters: 76×29.5×124.5 mm (H×W×D)
External Dimension:	VJCE Base: 130×482.6×121 or 177×482.6×121 mm (H×W×D)

Signal Conditioners

Product Name		Model	Output type			Standards
Product Name		Model	Isolated Dual-output	RS-485 Communication	Alarm (relay)
Isolator	Standartd Type	VJH1	√					√	√
	Multi-function	VJH7	√	√	√			√	√
	Super Speed Response Type	VJHF	√
	Reverse Output Type	VJHR	√					√	√
	Loop Powered Isolator	VJC1	√ ^{(Note 1)}
Distributor	Standartd Type	VJA1	√					√	√
	HART Communication	VJA1/H	√					√	√
	Multi-function	VJA7	√	√	√			√	√
	Square Root Extractor	VJA5	√					√	√
	Non-isolated	VJA4	√ ^{(Note 1)}			√ ^{(Note 2)}	√ ^{(Note 2)}
RTD Converter	Standartd Type	VJR6	√					√	√
Thermocouple Converter	Standartd Type	VJT6	√					√	√
Universal Temperature Converter	Multi-function	VJU7	√	√	√			√	√
CT Converter(RMS)		VJB1
PT Converter(RMS)		VJG1
AC Converter(RMS)		VJB3	√
Tachometer		VJD1	√
Potentiometer Converter	Multi-function	VJS7	√	√	√			√	√
Pulse Rate Converter	Standartd Type	VJP4	√
Pulse Rate Converter	Multi-function	VJP8	√	√	√	√ ^{(Note 2)}	√ ^{(Note 2)}
Pulse Repeater		VJP1	√
Pulse to Analog Converter	Multi-function	VJQ8	√	√	√	√ ^{(Note 2)}	√ ^{(Note 2)}
Analog to Pulse Converter	Standartd Type	VJQ0	√
Analog to Pulse Converter	Multi-function	VJQ7	√	√	√	√ ^{(Note 2)}	√ ^{(Note 2)}
High/Low Signal Selector		VJSS	√
Pneumatic to Electric Converter		VJF1
Ethernet/RS-485 Converter		VJET				√ ^{(Note 2)}	√ ^{(Note 2)}

Note 1: When 2 ch type is selected.
Note 2: Applicable when the power supply is 15-30 V DC.

VJ Mounting Base

Model	Product Name	Descriptions
VJCE	VJ Mounting Base	The multiple mounting base for VJ Series, mixed and housed up to 16 converters, JIS/EIA standards rack-mounting dimensions.

【Support Information】List of RoHS

This is a list of recorder and controller products that support the RoHS (2011/65/EU) directive.

See More
【Support Information】New Legislative Framework (NLF) Conforming Products

This is a list of recorder and controller products that support the New Legislative Framework (NLF.)

See More

Application Note

Constructing a Monitoring System Using Existing Sensors

Application Note

Implementing Control with a Backup Function

Application Note

Tank Level Control and Monitoring in Food Manufacturing Processes

Application Note

Compressor Anti-surge Control

Application Note

Connect Field Instruments and Upstream Devices with HART Communication compatible Signal Conditioners

Application Note

Adding Quantities of Flow Using a Signal Conditioner (Computation Unit)

Yokogawa Technical Report

JUXTA VJ Series Of Compact Signal Conditioners With Two Isolated Outputs

(rd-tr-r00026-009)

When I connect an open collector output conditioner with a counter or relay, it doesn't work.

(ns-faq-juxta-11017-spec)

The open collector needs a power supply. Use one within the maximum allowable load. ...

Can I change the burnout operation?

(ns-faq-juxta-11001-spec)

This is possible if it is a microprocessor type converter. You will need a handy terminal to make the change. (VJR6, VJT6, VJS2, MR6, MT6, MS2, and others cannot be changed.)

How is a handy terminal (JHT200) connected to a conditioner that allows range changes?

(ns-faq-juxta-11002-setting)

F and W series: dedicated 3-pin cable D series: dedicated 5-pin cable VJ, J, and M series computation unit: 5-pin cable + modular conversion (E9786WH, sold separately).

Can I change settings from a BT200 (BRAIN terminal)?

(ns-faq-juxta-11003-spec)

If it is a model that allows range changes, it is possible just like from a JHT200. However, the type of cable is different from the one that comes standard, so you will need to purchase another cable. 3-pin cable: model F9182ED 5-pin cable: model F9...

Can I change the range on the MQ0?

(ns-faq-juxta-11004-spec)

No, you can't change the range after purchase. The compact VJQ7 model does allow you to change ranges, but this requires a setting tool that is sold separately.

Can I change the range on the VJT6?

(ns-faq-juxta-11005-spec)

No, you can't change the range after purchase. The compact VJU7 model does allow you to change ranges, but this requires a setting tool that is sold separately.

How do I change settings?

(ns-faq-juxta-11006-setting)

Using the following settings tool, you can change the settings listed in the user's manual that came with the conditioner. Handy Terminals JHT-100 and JHT-200 BRAIN terminal BT200 (requires cable, sold separately) VJ77 Parameter Setting Tool...

What are the merits of plugin conditioners?

(ns-faq-juxta-11007-select)

They have the following advantages: Because you can separate the conditioner from the socket, panel work can proceed even without the conditioner. You can remove or replace the conditioner simply by plugging a new one in, so maintenance is easy. ...

How much resistance is there for current input?

(ns-faq-juxta-11010-spec)

The resistance is 250 Ω (4–20 mADC). However some computing units also have 100 Ω input.

What is the internal load resistance of pulse input?

(ns-faq-juxta-11011-spec)

You specify it for current pulse input. The resistance you specify depends on the specifications of the transmitter (mainly the rated current of the open collector). The internal load resistances are 200 Ω, 500 Ω, and 1 kΩ, and 0.5 ...

How do I determine the internal load resistance?

(ns-faq-juxta-11012-spec)

For example, if the specification of the open collector on the output side is 30 V/30 mA, use an internal load resistance of 1 kΩ (with a 24 V transmitter power supply). This results in a 0/24 mA current pulse.

There are Pt100 Ω standards of IPTS-68, ITS-90, and JPt100 Ω, but what is the difference between them?

(ns-faq-juxta-11013-other)

IPTS-68: This is an international standard from 1968 where R100/R0=1.3850 that was used by the JIS from 1989 to 1997, but currently it is not in use. ITS90: An international standard from 1990 where R100/R0=1.3851, and used by the JIS from 1997 to th...

How many instruments can be connected to a voltage output terminal (1–5 VDC)?

(ns-faq-juxta-11014-spec)

The input impedance of typical voltage input type instruments is 1 MΩ. By contrast, the allowable load impedance for voltage output is 2 kΩ or more, therefore the maximum number of units that can be connected is 500.

How many instruments can be connected to a current output terminal (4–20 mADC)?

(ns-faq-juxta-11015-spec)

The input impedance of typical current input type instruments is 250 MΩ. By contrast, the allowable load impedance for current output is 750 kΩ or more, therefore the maximum number of units that can be connected is 3.

What frequency setting should I use on an analog pulse converter when I want to output an integral pulse at 0.01㎥/P by using a 100㎥/H flowmeter?

(ns-faq-juxta-11016-spec)

100 × 1000/10/H = 10000/3600 Hz = 2.778 Hz (4 significant digits).

What does response speed **ms(10-90%) mean?

(ns-faq-juxta-11019-other)

It means the time until the output reaches 63% when input is applied in 10 Ω 90% steps.

There may be a 63% or 90% response depending on the manufacturer, but how should I compare these?

(ns-faq-juxta-11020-other)

A 90% response time is equivalent to 2.3 times the duration of a 63% response time.

What does "time constant" mean?

(ns-faq-juxta-11021-term)

In the case of conditioners, time constant reflects the response speed. In terms of a transfer function, it is expressed as OUT=INΩ(1-e EXP(-t/T)). OUT: output, IN: input, e: natural log, T: time constant, t: elapsed time When the elapsed time...

When ordering slide resistor conditioners, on models with total resistance, zero, and span resistance, what does total resistance mean?

(ns-faq-juxta-11022-other)

The total resistance ≥ zero side resistance + span resistance.

What is the output on burnout?

(ns-faq-juxta-11023-spec)

When UP, 106% of the output range or more; when DOWN, -6% or less.

What happens on a "burnout OFF"?

(ns-faq-juxta-11024-spec)

When input is interrupted it reaches ±OVER, but which of these is uncertain.

About how many computations can be included?

(ns-faq-juxta-11027-spec)

The F series has 30 steps. The W series has 40 steps. The M/VJ series has 59 steps.

What are the computation intervals of computing units?

(ns-faq-juxta-11028-spec)

On the M series you can select 50, 100, or 200 ms. On the F, W, and VJ series you can select 100 or 200 ms. (The VJXS can support 50 ms.)

Is an externally attached resistance for current input included?

(ns-faq-juxta-11033-select)

It is with plug-in types. It is also sold separately.

Do you have any conditioners that support HART communication?

(ns-faq-juxta-11034-select)

A distributor for the V series (VJA1/H), and a distributor (DA7) and isolator (DC7) for the D series are available.

How can I suppress ripple noise on the instrument's input signal?

(ns-faq-juxta-11035-spec)

Using a first-order lag or moving average computing unit helps suppress noise. You can use the following for this: M series plug-in type signal conditioners, VJ series compact plug-in type units, or F/W series front panel terminal type computing unit...

Are there any models that allow me to set up an upper or lower limit limiter on the instrument's input signal?

(ns-faq-juxta-11036-select)

You can do this with a limiter or broken-line approximation function. You can use the following for this: M series plug-in type signal conditioners, VJ series compact plug-in type units, or F/W series front panel terminal type computing units. The br...

Can I attach the VJ and M series horizontally?

(ns-faq-juxta-11037-other)

As the orientation affects heat dissemination, it cannot be horizontal.

What is the model of the VJ series terminal block (socket)? Can I use an Omron socket?

(ns-faq-juxta-11032-select)

It’s model T9093FL. The VJ socket is built with holes for screws that prevent falling off, therefore an Omron socket cannot be used.

Does the JUXTA VJ series support CCC and GB standards? Can it be used in China?

(ns-faq-juxta-11038-other)

JUXTA VJ series is not a CCC standard scope. Some models of the VJ series have acquired GB standard and can be used in China. Please contact us for applicable models. ...

The VJ series can come with a second output for RS-485 communication, but can I change VJ series parameters on upstream devices (PCs or PLCs) using this communication? Ex.: Changing the VJP8 pulse rate setting via RS-485 communication

(ns-faq-juxta-11040-spec)

Because the RS-485 communication on output 2 is reserved for I/O or error status monitoring, it cannot be used to write parameters.

If installing lightning arresters between: transmitter →safety barrier (BARD)→distributor (VJA7), are there any restrictions on where I can place them?

(ns-faq-juxta-11041-select)

As our lightning arresters are not explosion proof, they cannot be used in the configuration of instruments you described.

I purchased the VJ series, but I can't remove the main unit from the socket.

(ns-faq-juxta-11047-connect)

The black knob on the front panel is the screw that secures the main unit. Turn it counterclockwise to loosen, then remove the unit.

I purchased an isolator with a 4-20 mA current input specification. Can I use it with voltages of 1-5 VDC?

(ns-faq-juxta-11049-connect)

Yes. Wire it without using the included resistor.

Is there a converter that converts voltage pulse to a non-voltage contact?

(ns-faq-juxta-11050-select)

We have pulse repeaters such as the VJP1, and VJP8.

Can you ship the VJ series alarm setter with preset alarm types and values?

(ns-faq-juxta-11051-spec)

It is shipped with factory default settings. Alarm types and values should be set by the user with a handy terminal or the VJ77 parameter setting tool.

With a 2 output type signal conditioner, when not using a current output terminal, how should I handle the terminal processing?

(ns-faq-juxta-11052-connect)

Short with a 250 Ω resistor (rated power of 0.25 W or more). If you don't have a resistor, a simple short is fine.

There's no output with an isolator. What should I do?

(ns-faq-juxta-11055-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. Check the polarity of the input wiring. Use a tester to measure the input terminal voltage. For current input specifications, confirm that the acces...

There's no output with a distributor. What should I do?

(ns-faq-juxta-11056-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. Check the polarity of the input wiring. Measure the voltage between the input terminal (-) and COM. The normal range is 1–5 VDC. Measure the v...

There's no output with a thermocouple temperature converter. What should I do?

(ns-faq-juxta-11057-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. Confirm that the accessory RJC sensor is connected to the input terminal. Short the input terminals, then confirm that the output is equivalent to th...

There's no output with an RTD temperature converter. What should I do?

(ns-faq-juxta-11058-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. For Pt100 input specifications, connect a 100 Ω resistance between input terminals A and B, short the B terminals, then confirm that the output ...

There's no output with a pulse signal repeater and pulse rate converter. What should I do?

(ns-faq-juxta-11059-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. Check the polarity of the input wiring. Check the pulse specifications of the other instruments. For voltage pulse, open collector, and non-voltage ...

There's no output with an analog/pulse converter. What should I do?

(ns-faq-juxta-11060-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. Check the polarity (+), (-) of the input wiring. Use a tester to measure the input terminal voltage. For current input specifications (applies to the...

There is no output with a pulse/analog converter. What should I do?

(ns-faq-juxta-11061-connect)

Check the power supply wiring. Check whether the power supply voltage meets the specifications. Check the polarity of the input wiring. Check the pulse specifications of the other instrument. For voltage pulse, open collector, and non-voltage c...