CIS CIS   
Съёмное шасси DX1000N
OpreX-Средства сбора данных

Съёмное шасси DX1000N

Использование на установках и в диспетчерских пунктах требует повышенной надежности записи и мониторинга данных. Помимо надежного сбора данных, использование в условиях устновок и диспетчерских пунктов также требует быстрого и простого технического обслуживания. DX1000N компании Yokogawa сертифицирован для использования в атомной энергетике и широко применяется на установках и в диспетчерских пунктах.

DX1000N обеспечивает лучшую в отрасли надежность и точность измерений. Съемное шасси обеспечивает быстрое и простое техническое обслуживание, сокращая время простоя. DX1000N легко подключается к вашей сети для передачи необходимых данных непосредственно в существующую инфраструктуру.

Особенности

Новый DXAdvanced DX1000N оснащен внутренним шасси, которое может быть извлечено из корпуса через переднюю панель прибора. Это обеспечивает доступ ко всем внутренним компонентам DX1000N с панели управления без необходимости доступа к задней части устройства или без нарушения существующей электропроводки. Функциональность, внешний вид и размеры выреза в панели такие же, как и у стандартной модели DX1000.

Основные функции

  • До 12 входных каналов
  • Запуск / остановка пакетной записи и создание файлов данных
  • Возможность расширения с помощью функции автоматического подключения MW100
  • Объем внутренней памяти увеличен до 400 МБ
  • Позволяет управлять планированием коррекции на поправки [R4]
  • Автоматическое создание таблиц Excel на основе шаблонов [R4]

Дисплей и управление

  • Вы можете настроить экран по своему усмотрению с помощью функции пользовательского дисплея!
  • Просмотр архивных данных с помощью функции поиска по дате и времени

Сетевые функции

  • Стандартный интерфейс Ethernet
  • Поддерживает протоколы PROFIBUS-DP и EtherNet/IP!
  • Расширенные веб-функции и сетевые функции!

Надежность и безопасность 

  • Соответствие FDA 21 CFR, Часть 11, с опцией расширенной функции безопасности [R4]
  • Пыле- и брызгозащищенная передняя панель (IP65, NEMA4)
  • Внутрення память высокого уровня надежности с функцией устранения ошибок
  • Блокировка дверцы передней панели и функция входа в систему

Прикладное программное обеспечение

  • Программное обеспечение для различных задач, включая анализ, изменение настроек и сбор данных

 

Подробно

DAQManager DX250 (продается отдельно)

Программное обеспечение для управления данными для безбумажных регистраторов

DAQManagerDAQManager – это программное обеспечение, которое позволяет управлять данными измерений от Daqstation и безбумажных самописцев MVAdvanced на ПК. Данные, загруженные в DAQManager, можно быстро и легко найти по дате / времени, тегу, названию партии и по другим критериям. Данные, записанные с разных инструментов и в разные периоды времени, могут отображаться на одном и том же графике тенденций.

* DAQManager не поддерживает модели с расширенной функцией безопасности (/AS1).

  • Индексирование для обеспечения возможности быстрого поиска
  • Разнообразие графиков
  • Простая загрузка / импорт данных
  • Автоматическое слияние данных

DAQStudio DXA170 (продается отдельно)

Программное обеспечение для настройки параметров экрана

Программа-компоновщик позволяет редактировать и создавать пользовательские экраны на ПК. Вы можете отправлять и получать данные о компоновке, а также легко редактировать и создавать объекты.

  • Отправка / получение данных о компоновке для настройки экранных объектов (через Ethernet или CF-карту)
  • Отображение настраиваемых экранов дисплея, создание новых экранов и редактирование существующих экранов
  • Сохранение / загрузка настроек и отредактированных файлов данных

DAQStudio

DAQSTANDARD DXA120

DAQSTANDARD – это стандартный пакет программного обеспечения, входящий в комплект поставки DXAdvanced. Его можно использовать для вывода данных печати или повторного отображения файлов архивных данных, сохраненных устройством DXAdvanced или переданных по протоколу FTP.

DAQWORX (продается отдельно)

DAQWORX – это пакет программного обеспечения для сбора данных, который объединяет регистраторы Yokogawa, приборы для сбора данных и измерительные приборы.

DAQEXPLORER

DAQEXPLORER – это специальное ПО для серий DX, CX и MV, которая предлагает сочетание функций передачи файлов, мониторинга на базе ПК и других функций в дополнение к функциям DAQSTANDARD. Оно обеспечивает простой доступ к широкому спектру сетевых функций DXAdvanced.

Особенности и преимущества

DAQWORX позволяет пользователям организовать систему сбора данных с использованием устройств записи данных, регистраторов, контроллеров температуры, измерительных приборов Yokogawa без необходимости программирования. Для расширения функциональности DAQWORX предлагает интегрированную систему сбора данных, позволяющую заказчикам подключать программное обеспечение высокоразвитым графическим интерфейсом к системам сбора данных, чтобы легко расширить количество поддерживаемых приложений.

Интегрированный пакет

  • Интеграция регистраторов, контроллеров и измерительных приборов

Пакет для конкретного оборудования

  • Получите максимум пользы от каждого отдельного продукта
  1. DAQ32Plus (для серии Darwin)
  2. MXLOGGER (для DAQMASTER MX100)
  3. DAQEXPLORER (для DX, CX и MVAdvanced / MV)
     

    *: Данный продукт снят с производства

    CX*: Продукт на замену – безбумажный регистратор GХ/GP серии SMARTDAC+

    MV*, Darwin *: Продукт на замену – система сбора данных GM серии SMARTDAC+

Общее программное обеспечение

  • Обозреватель данных

ПО для регистрации данных GA10 (продается отдельно)

Программное обеспечение для регистрации данных, которое обеспечивает одновременное использование Ethernet и последовательной связи. Комбинация устройств сбора данных DXAdvanceds, DARWIN и регистраторов uR (всего 100 единиц) позволяет обеспечить сбор данных по 2000 каналам.

Файлы

Application Note
Managing Sterilization through Calculation of the Fo Value
Thumbnail
Обзор:

The paperless recorder DX series automatically calculate the Fo value from the heating temperature and are useful in managing the sterilization process by displaying and recording the value together with the heating temperature.

Отрасли:
Application Note
Measurement Optimization in the Water Industry
Thumbnail
Обзор:

The control of the world's water resource is arguably one of the most important issues. Water demand from industry and domestic users is set to rise throughout the industrialized world. Yokogawa has been applying minimized maintenance measurement systems.

Отрасли:
Application Note
Monitoring Temperature and Humidity
Thumbnail
Обзор:

The paperless recorder DX series instruments allow you to determine temperature and humidity, and manage the results as manufacturing and quality data at a reasonable cost with a simple configuration.

Отрасли:
Does the product support FDA 21 CFR Part 11?
(ns-faq-dxadvanced-1001-select)
The DX series does with the advanced security option (suffix code /AS1).
Can the Advanced security and Multibatch functions be used together?
(ns-faq-dxadvanced-1002-spec)
Yes, you can use the Advanced security option (suffix code: /AS1) and the Multibatch function option (suffix code: /BT2) together.
Can I use the PROFIBUS-DS communication interface and Advanced security function together?
(ns-faq-dxadvanced-1003-spec)
Yes, you can use the PROFIBUS-DP communication option (suffix code: /CP1) and the Advanced security function option (suffix code: /AS1) together.
Can I use pulse input and the MATH function together?
(ns-faq-dxadvanced-1004-spec)
The pulse input option (suffix code: /PM1) includes the MATH function option (suffix code: /M1). By adding the pulse input option, you can also use the MATH function. It is not necessary to add both options together.
Can I change SNTP settings during data acquisition?
(ns-faq-dxadvanced-1007-setting)
No. When changing settings, data acquisition stops.
When using remote control input to set the time with external contact input, can I specify the time?
(ns-faq-dxadvanced-1008-spec)
No, the time cannot be specified.
With the pulse input option, what is the maximum number of pulses that can be acquired?
(ns-faq-dxadvanced-1010-spec)
The pulse input option (suffix code: /PM1) provides 3 dedicated pulse inputs plus 5 remote control common terminals for a total of 8 acquisitions. Integral values can also be calculated on individual MATH channels.
Can I change the display language on the main unit?
(ns-faq-dxadvanced-1011-spec)
Yes. You can change it to Japanese, English, German, French, or Chinese.
Can you tell me the specifications of the remote control function option (suffix code: /R1)?
(ns-faq-dxadvanced-1009-spec)
There are 8 input terminals. They are of the non-voltage contact and open collector types. The signal types are level and edge (250 ms or higher).
Can I customize display screens?
(ns-faq-dxadvanced-1013-spec)
Yes, with R3 (release 3). With DAQStudio (DXA250) screen editing software, you can easily create custom display screens.
Can I connect the MW100 and DXAdvanced via Modbus/TCP and load the MW100's measured data on the DX main unit?
(ns-faq-dxadvanced-1014-connect)
Yes. However, the DX1000/DX1000N requires the MATH function option (suffix code: /M1), and the DX2000 requires the expansion channel function option (suffix code: /MC1) or the MATH function option (suffix code: /M1).
Can I increase the number of inputs above 48 ch?
(ns-faq-dxadvanced-1015-spec)
You cannot increase the number of input terminals. However, you can load data acquired on other instruments such as the MW100 onto the DX via communications.
Are Modbus communications enabled by adding the RS-422A/485 interface option?
(ns-faq-dxadvanced-1016-connect)
Yes. Adding the RS-422/485 communication interface option (suffix code: /C3) makes the DX a Modbus/RTU subordinate, enabling communications with Modbus master devices. Note that making the DX the Modbus master requires the MATH function option (suffi...
Are there safeguards against data tampering?
(ns-faq-dxadvanced-1019-spec)
Saving measured data in binary format prevents it from being tampered with.
I've added the advanced security function option and the PROFIBUS-DP communication interface option. During PROFIBUS communication, does the security function have any effects or restrictions on PROFIBUS communication such as login or password entry?
(ns-faq-dxadvanced-1020-spec)
Even when the advanced security option (suffix code: /AS1) is running, PROFIBUS communication can proceed without restriction. No login via ID or password is required.
If I've added the advanced security function option, can I set up any restrictions on saving data to USB memory?
(ns-faq-dxadvanced-1021-spec)
Yes. With the user login function, you can set operations for each user.
If I'm using the advanced security function option and Multibatch function option together, can I change the ranges and alarms for non-recording groups while Multibatch group 1 is recording?
(ns-faq-dxadvanced-1023-setting)
When using the Multibatch function option (suffix code: /BT2), you cannot change the range even if group 1 is recording, regardless of any other options. However, you can edit alarm settings during recording.
When a power failure occurs, is the data just before the power failure saved?
(ns-faq-dxadvanced-1012-spec)
Yes, the internal memory is non-volatile memory, therefore the data just before the power failure is saved. When the instrument recovers from a power failure, data acquired just before the power failure are saved as files to internal memory. Also, da...
Can I start/stop recording using the remote control input option even when using the advanced security function option?
(ns-faq-dxadvanced-1022-spec)
Yes. For details, see "Event Action Function " and "Remote Control Function " in the user's manual. DX1000 user's manual DX2000 user's manual ...
Can I connect two DX units with a LAN and perform Modbus/TCP communications?
(ns-faq-dxadvanced-1025-connect)
Yes. However, this requires the MATH function option (suffix code: /M1) on the unit that is displaying (recording) data.
With the FTP client function, if FTP file transfer to the FTP server stops due to network interference or other reasons, how do I handle the files that were not able to be sent?
(ns-faq-dxadvanced-1027-connect)
Unsent files will be sent upon the next FTP transfer.
I have a DX main unit set up for Ethernet communications with 2 PCs. If I'm acquiring data from the DX via Modbus/TCP on 1 PC, can I acquire instantaneous values using applications such as DAQLOGGER at the same time on the other PC?
(ns-faq-dxadvanced-1028-connect)
Yes. The communication port used by Modbus is different than the one that can acquire instantaneous values, so simultaneous communication is possible.
If acquiring other instruments' data via Modbus communications, can I display those values in a custom screen?
(ns-faq-dxadvanced-1029-connect)
Yes. You can also display communication input channels, MATH channels, and expansion channels.
Can you tell me about the "Time difference settings" in the FTP transfer settings?
(ns-faq-dxadvanced-1030-spec)
When the FTP server gets file transfer requests from multiple DXs or other instruments, it cannot handle all of those requests at once. This setting delays the transfer times to avoid errors.
What is the lifespan of the built-in battery for saving settings?
(ns-faq-dxadvanced-1031-spec)
For best results, we recommend replacing the built-in lithium battery every 10 years. Note that battery replacement should be performed by a trained Yokogawa technician. Please contact your nearest dealer or Yokogawa representative.
Can you tell me about the calibration scheduling function?
(ns-faq-dxadvanced-1032-spec)
This function allows you to control periodic entering of settings for the calibration function option (suffix code: /CC1). When you enable the calibration function, a screen appears that displays the calibration due date in advance (the calibration n...
Can I start/stop recording based on external contact and then automatically save data to the CF card when recording is stopped?
(ns-faq-dxadvanced-1033-spec)
Yes, this is possible by adding the remote control function option (suffix code: /R1) and using the event action function. Note that you can also automatically save data to the CF card while recording is stopped.
Can I load data files from a recorder's internal memory onto a PC?
(ns-faq-dxadvanced-1034-spec)
Yes, when the FTP server is ON.
Can I automatically save data files on USB memory?
(ns-faq-dxadvanced-1035-spec)
No. Due to reliability issues with recording media, you can only save data automatically onto the CF card. The USB memory is only intended for temporarily transferring data files.
Please let me know what to do if the free space on the DX1000 / DX2000 / DX1000N CF card is exhausted.
(ns-faq-dxadvanced-1037-spec)
Insert the CF card into the PC and move the data file to the PC hard disk. You can view the data file saved on your PC with the DAQSTANDARD software that comes standard with the DX.
Do the CF card and card adapter come with DX1000 / DX2000 / DX1000N when it is delivered?
(ns-faq-dxadvanced-1039-other)
Only CF card is included. Card adapter is not included. The CF card can be used by inserting it directly into the main unit.
Is there a limit on the number of files created on the CF card when using the function (media FIFO) that can always keep the latest data file on the CF card?
(ns-faq-dxadvanced-1040-spec)
When using the function that always keeps the latest data file on the card (Media FIFO) and the number of files in the same directory exceeds 1000, CF card deletes the old data file and saves new one even if there is free space on the card.
Is there a warning when the CF card starts running out of free space?
(ns-faq-dxadvanced-1041-spec)
Yes. When there is 10% of free space or less, the CF card icon on the upper part of the display turns from green to red.
Even though I inserted the CF card, the CF card icon in the upper part of the screen shows an X.
(ns-faq-dxadvanced-1042-spec)
There may be a problem with the CF card. Try the following. Eject, then reinsert the CF card. Replace the card. Reformat the card on the DX.  
Can I eject the CF card during recording?
(ns-faq-dxadvanced-1043-spec)
Yes, if the CF card is not being accessed. To eject it, press the Func key, then select Eject media > CF.
Do you carry any CF cards that have been operationally validated?
(ns-faq-dxadvanced-1036-spec)
Yes, the following: 772093: 512 MB 772094: 1 GB 772095: 2 GB  
Is the DX1000 / DX2000 / DX1000N CF card standard TYPE1 or TYPE2?
(ns-faq-dxadvanced-1038-spec)
It is TYPE1.
When the media FIFO function is OFF, a message appears when there is insufficient free space on the CF card, but what happens to the data after the message? What happens when transferring files via FTP?
(ns-faq-dxadvanced-1044-spec)
When the CF card becomes full, files continue to be created in the internal memory. The files created in internal memory are also transferred via FTP.
Is report data saved on the CF card?
(ns-faq-dxadvanced-1045-spec)
As with recorded data, files are saved to the CF card after being created in internal memory if the auto save function is ON. Hourly reports are saved every hour, and daily reports are saved every day.
Can you tell me about the functions of DAQSTANDARD?
(ns-faq-dxadvanced-1047-soft)
DAQSTANDARD is composed of 2 programs. Viewer: You can display measured data as trends or numeric values, and print them. Plus, binary data files can be exported to ASCII or Excel format. Hardware configurator: You can create settings files for a...
Can I display and analyze recorded data on a PC?
(ns-faq-dxadvanced-1048-spec)
Yes, by using the DAQSTANDARD software that comes standard.
Can you tell me what user's manual or software CD is included in the packaging upon delivery? [DX1000/DX2000]
(ns-faq-dxadvanced-1051-other)
The following printed materials are included: “Managing Product Waste,” and “Open Source Software Specifications.” A CD with other user’s manuals and the DAQSTANDARD software are currently not included. (Separately purch...
Is a warranty card included?
(ns-faq-dxadvanced-1052-other)
The warranty is handled with the DX serial number, so a printed warranty card is not included. The warranty period is one year from date of purchase.
Do I need additional software to create custom display screens?
(ns-faq-dxadvanced-1049-soft)
To create them on a PC you will need the DXA170 DAQStudio custom display builder software, sold separately. You can create them by using keys on the main unit, but it is much easier by using DAQStudio. DAQStudio Product Page ...
Which compact flash cards (CF cards) have been validated?
(ns-faq-dxadvanced-1053-spec)
Please see the following. List of validated compact flash (CF cards)
I cannot open data files in DAQSTANDARD.
(ns-faq-dxadvanced-1046-soft)
You may have an older version of DAQSTANDARD. Consider upgrading to the latest version. You can download the latest version by using the following link. DAQSTANDARD download page *Log-in Required ...
By using the main unit FTP server function, can I acquire recorded data files from the main unit CF card or internal memory onto a PC on a local area network?
(ns-faq-dxadvanced-1057-connect)
Yes, by using 3rd party FTP client software.
What are the supported e-mail authorization methods?
(ns-faq-dxadvanced-1059-spec)
They are "AUTH PLAIN " and "AUTH CRAM-MD5. " AUTH-LOGIN is not supported.
Can I adjust the main unit time during recording?
(ns-faq-dxadvanced-1060-spec)
Yes, you can adjust it directly on the main unit even during recording. If you adjust the time during recording, the acquired data is time-stamped with the new time.
The data list doesn't appear in the web server screen.
(ns-faq-dxadvanced-1061-spec)
The following conditions must be met in order for the data list to appear in the web server screen. The FTP server must be turned ON. Login via communication must not be set. Note that the data list never displays on models with the advanced se...
What happens if I mis-enter the user ID and password multiple times?
(ns-faq-dxadvanced-1063-spec)
You can set the number of password retries to 3, 5, or unlimited (default is 3). When the number of retries is exceeded, the unit is locked. Service is required to clear the lock, so please manage user IDs and passwords with care. Note that if 1 unit...
I'm using the DAQSTANDARD hardware configurator and I want to edit settings on the DX1000/DX2000 via Ethernet, but communication isn't working.
(ns-faq-dxadvanced-1054-connect)
  Connect the PC and DX via a hub. If the connection is working, the Link LED on the PC, hub, and DX should all light. Check the PC's IP address and subnet mask using the ipconfig command. Check the DX's IP address and subnet mask i...
How do I wire the terminals and what is the diameter of the terminal screws?
(ns-faq-dxadvanced-1055-spec)
For terminal wiring, see the section on grounding and wiring in the operation guide. DX1000 Operation Guide DX2000 Operation Guide The diameter of all the screws is 4 mm. DX1000 Operation Guide DX2000 Operation Guide   ...
Can I view data that was recorded onto the CF card on a PC?
(ns-faq-dxadvanced-1056-spec)
Yes, by using the accessory software DAQSTANDARD (model DXA120). See chapter 3, "Viewing Recorded Data " in the operation guide. For further details, see the viewer's user's manual. DXA120 user's manual ...
If a power failure occurs while reports are being created, is the report up to the failure created?
(ns-faq-dxadvanced-1058-spec)
No, but the creation of the report restarts after recovery from the power failure. The operation is different depending on whether the recovery time is before or after the report creation time has elapsed. For details, see "Special Data Handling...
How do I change the measured data interval (recording interval)?
(ns-faq-dxadvanced-1062-setting)
The DX has two kinds of files, DISP (display data) and EVENT (event data). You can tell which type the data is by looking inside the blue band in the upper part of the screen. In the case of (2) DISP (display data), the sampling interval changes i...
Can I automatically convert recorded data files to Excel?
(ns-faq-dxadvanced-1065-spec)
Yes. With DAQManager, you can specify the folder containing the recorded data files as the auto-import destination, then set it for automatic conversion to Excel. Note that this is not supported with addition of the advanced security option (suffix c...
On DAQSTANDARD, how can I receive settings from a DX with the advanced security function (a DX1000/DX1000N/DX2000 with the /AS1 option)?
(ns-faq-dxadvanced-1076-spec)
You can receive settings by using the user management "Monitor" function specific to advanced security. The Monitor function enables up to 2 connections. When 2 Monitor functions are connected on the network, you can receive settings. ...
Is account information available from the settings file of a DX with the advanced security option (suffix code /AS1)?
(ns-faq-dxadvanced-1078-spec)
No.
When loading settings on a DX with the advanced security option (suffix code /AS1), are there any precautions when using "All settings" in Basic setting mode?
(ns-faq-dxadvanced-1079-spec)
Yes, note that the passwords in the account information will be initialized.
Can I compare settings? And can I also compare data from the advanced security option (suffix code /AS1)?
(ns-faq-dxadvanced-1064-spec)
Yes, by printing the settings from the DAQSTANDARD (accessory software) hardware configurator. For details, see section 1.5, "Printing Setup Data" in the DAQSTANDARD hardware configurator user's manual. DAQSTANDARD user's manual ...
What should I do if I lost my DAQSTANDARD license number?
(ns-faq-dxadvanced-1066-spec)
We have a special license number available in case of lost licenses. See the following URL. Universal keys in case of lost licenses *Log-in Required
Is there a simple way to test from a PC whether I can log on to a DX that is connected via Ethernet?
(ns-faq-dxadvanced-1077-spec)
You can use the Windows telnet command. Click Start > All programs > Accessories > Command Prompt. At the command prompt, type "telnet. " Given a DX IP address of "10.1.32.130," type the following (the port number is...
When testing the FTP client settings, the following error appeared: E282 An error occurred with the FTP controller connection. What should I do about this?
(ns-faq-dxadvanced-1080-spec)
Communication could not be established with the FTP server. You can check details on codes in the FTP log screen. In the FTP log screen, while DX1000/DX2000 is running, press the DISP/ENTER key. In the operation menu on the left side of the screen, m...
During recording the following error appeared: "E501 Insufficient free space on media." Can I have it automatically delete old files when there is no more free space on the CF card?
(ns-faq-dxadvanced-1081-spec)
Yes, turn ON the media FIFO function. If the CF card does not have sufficient free space, or if there are 1000 files or more, old files will be overwritten with new ones. For details on the media FIFO function, see Explanation of functions: Data Sav...
In the DAQSTANDARD viewer, if you connect to files that were divided by the Auto save on the DX, several trigger marks will appear. Is there any way to clear those trigger marks?
(ns-faq-dxadvanced-1082-soft)
Yes. Select a trigger mark with the cursor, then click Edit > Delete Mark. For details, see section 2.2, "Displaying Waveforms " in the DAQSTANDARD Viewer user's manual. User's manual download   ...
I set a trip line in the DAQSTANDARD viewer but it doesn't appear in the trend. How can I display it?
(ns-faq-dxadvanced-1084-soft)
If assigned to multiple channels, display the trip line of the active waveform. Click the color bar on the left side of the viewer, and activate the waveform of the channel on which you set the trip line.
How many DAQSTANDARD licenses are there? I want to view multiple PCs to view data files recorded on the DX series, but do I have to install it on each PC?
(ns-faq-dxadvanced-1085-soft)
For DAQSTANDARD software licenses, see "Terms and Conditions of the Software License" in the user's manual. The number of licenses is 1. To use multiple PCs, download SMARTDAC+ STANDARD Universal Viewer. ...
When attempting an electronic signature using DAQSTANDARD Viewer, error E0211, "Can't write to file." appears. It is not a matter of insufficient space for the folder contents, or another program accessing the contents. My OS is Windows 7.
(ns-faq-dxadvanced-1086-soft)
Check your Windows 7 rights. If you don't have write permission, change your permissions.
When attempting an electronic signature with DAQSTANDARD Viewer, error E0210, "Not registered user." appears. My user name, ID, and password are correct, and I confirmed my signature privileges on the main unit.
(ns-faq-dxadvanced-1087-soft)
It is possible that the user has expired and the password has returned to the default, or some similar problem. See section 2.10, "Signing Batch and Continuous Data" in DXA120 DAQSTANDARD Viewer User's Manual. ...
I'm using dedicated DX communication commands to communicate with the Mitsubishi MELSEC. The first command is accepted, but I get no response from any subsequent command (even the same one as the first command). What could be the problem?
(ns-faq-dxadvanced-1088-connect)
Some commands are sent in units of words. This always results in an even number of bytes. But if you send the command "FD0,1,1CRLF", for example, that is an odd number of bytes (9), and the 10th byte which follows CRLF will be populated wit...
Can I use encrypted USB memory?
(ns-faq-dxadvanced-1089-spec)
No. Encrypted USB memory is not supported.
I'm trying to start/stop recording by using a remote signal on a DXAdvanced series model with remote control (/R1). After starting recording with a remote signal, if I accidentally press the stop key, does recording continue or stop?
(ns-faq-dxadvanced-1091-setting)
After starting with a remote signal, if you press stop, a confirmation message appears. If you select to stop recording, it stops. If you use key lock on the stop key, recording won't stop even if you accidentally press the stop key during record...
Can I display "Legend" in DAQSTANDARD Viewer's trend graph?
(ns-faq-dxadvanced-1083-soft)
No, but you can with the SMARTDAC+ universal viewer. The SMARTDAC+ universal viewer supports data from the DX and MV series, and is available for free download from our Web server. SMARTDAC+ Standard Universal Viewer download page *Log-in Required ...
When I try to open data files saved to the CF card by the DXAdvanced series on DAQSTANDARD Viewer, the message, "E0212 Could not read file" appears.
(ns-faq-dxadvanced-1090-soft)
You may be using an older version of DAQSTANDARD Viewer. Please download the latest version of DAQSTANDARD (DXA120) *Log-in Required from our website.
Can you tell me where to get (download) the latest version of DAQSTANDARD?
(ns-faq-dxadvanced-1092-soft)
Please download the latest version of DAQSTANDARD (DXA120)* from our website. Also, if you lost your license number, please see "Universal keys in case of lost licenses."* *Log-in Required ...
I'm inputting 1-5 VDC on the DXAdvanced series and using linear scaling. Can I expand the trend display area by narrowing the upper and lower limit of the scale?
(ns-faq-dxadvanced-1094-setting)
Yes. If you narrow the lower and upper-limit values, change the lower and upper-limit values of the span accordingly.
In the DXAdvanced series, there is no bias function for adding or subtracting a specific value to or from the input value. How can I display the measured temperature as 0.5°C higher than the actual input?
(ns-faq-dxadvanced-1096-setting)
In the input range settings, you can add a specific value in the same manner as a bias setting by selecting a scale. Ex) Set a thermocouple Type-K span of 0-100 DEGC. To display the temperature 0.5DEGC higher, set the following in the input range set...
With the DXAdvanced series, can I save measured data in CSV format?
(ns-faq-dxadvanced-1100-spec)
The DX1000/DX2000 can save measured data in binary format. You can convert saved measured data to ASCII (CSV) format using DAQSTANDARD Viewer.
On the DXAdvanced with the USB interface option (/USB1), where on the main unit do I attach the USB interface?
(ns-faq-dxadvanced-1098-spec)
There are two locations, one on the front and one on the back. On the front, it's inside the front panel door next to the CF card slot. On the back, it's next to the Ethernet interface.
On a model with the PROFIBUS-DP communication option (/CP1), I want to change to Modbus/TCP communication. Is there anything I need to be careful of?
(ns-faq-dxadvanced-1102-spec)
With the DX1000, you cannot use communication channels. On the DX2000, use communication channels C33–C60 (with the MATH option /M1, you can't use C01–C32).
When a DXAdvanced series measured value is +Over or -Over, RANGE OVER is displayed. In what cases does an overrange occur?
(ns-faq-dxadvanced-1093-spec)
The conditions under which an overrange occurs depends on the input range mode settings. For details, see the note under "Digital Display" in section 1.3 of the User's Manual. ...
I configured the Modbus client function on the DXAdvanced series, but I can't connect to the Modbus server. Can I check the Modbus operation status?
(ns-faq-dxadvanced-1095-setting)
Yes, press the DISP/ENTER key, and then select [INFORMATION] > [MODBUS CLIENT]. In order for [MODBUS CLIENT] to appear in the screen menu, you must configure it in the menu customization function. See "Checking the Modbus Operating Status&quo...
I'm configuring the DXAdvanced series advanced security model (/AS1). When registering a system administrator in the user registration screen, it only lets me set the "Default Password." How can I set my own password?
(ns-faq-dxadvanced-1097-setting)
In the user registration screen, first set the default password. The first time you log in, enter the default password. The message, "Your password has expired. Key in your new password" appears, and you can enter a new password. For more i...
I'm using a DXAdvanced series model with the USB interface option (/USB1). How can I copy data in internal memory to the USB memory?
(ns-faq-dxadvanced-1099-setting)
In the User's Manual, see section 2.12, "Using the USB Flash Memory (/USB1 Option)" and see "Saving the Data" in section 4.8, "Using the Memory Summary." ...
I'm using a DXAdvanced series advanced security model (/AS1). When logging in, I entered the wrong password several times, and the user locked icon appeared. How can I log in?
(ns-faq-dxadvanced-1101-setting)
See "Dealing with the Invalid User Status" in section 2.2, "Logging In and Out" in the advanced security function (/AS1) user's manual. If all system administrator passwords are invalidated, please contact your Yokogawa servi...
RTD measurement with the BARD-700
(ns-faq-dxadvanced-1103-spec)
Q: With RTD input, the input source resistance is described in section 13.6, “General Specifications” of the user manual as: “10Ω or less per wire (the resistance of all three wires must be equal).” I'm using the BAR...
When report data 100/100 is displayed, how do I view report data 101 and beyond?
(ns-faq-dxadvanced-1104-spec)
The data is saved automatically to the CF card (with the extension, DAR). You can display it on a PC using DAQSTANDARD.
How many amperes should I select for the DXAdvanced series power supply circuit breaker?
(ns-faq-dxadvanced-1105-spec)
This will be the same as the switch specifications in the operation guide. No /P1 option: Steady-state current rating 1 A or highter, inrush current rating 60 A or higher. With /P1 option (with 24 VDC/AC power supply): Steady-state current rating 3 A...
I'm inputting 1 - 5 VDC on the DX1000/DX2000 and using scaling of 0.0 - 200.0%. How do I calculate the overall accuracy?
(ns-faq-dxadvanced-1106-spec)
The measurement accuracy of the 1-5V range is ±(0.05% of rdg＋3 digits), and the maximum digital display resolution is 1 mV. Formula becomes "measurement accuracy during scaling (digits) = measurement accuracy (digits) × scaling span...
How many reference junction compensation (RJC) temperature sensors are included with the DX1000 and DX2000?
(ns-faq-dxadvanced-1107-spec)
One RJC temperature sensor is included with each input terminal block.
You can display blue and black measured values in the historical trend display. Which values are being displayed?
(ns-faq-dxadvanced-1109-spec)
The blue values are the maximum/minimum values at the cursor. The black values are the maximum/minimum values of the entire display area.
Can I view files that are undergoing memory sampling on a PC?If you view the memory summary, "Sampling" is displayed for the factor.
(ns-faq-dxadvanced-1110-setting)
During memory sampling, you can use key operations to save data or event data. In Operation mode, press the FUNC key, then press Save display or Save event soft key.
With the /F1 FAIL/Status output option, there's a memory sampling output setting (only on a DX with the advanced security option (/AS1)) and an output device information on memory stop (status relay) setting. What is the difference between these two?
(ns-faq-dxadvanced-1111-spec)
With memory sampling output, the relay is energized on memory start, and deenergized on memory stop. With the output device information on memory stop setting, the relay is energized when you stop memory sampling. These actions cannot be changed. ...
Can I use output from a differential pressure transmitter as input, and then perform square root computation?
(ns-faq-dxadvanced-1112-setting)
Yes. Choose Sqrt for the input range mode.
The interval of the high limit on rate-of-change alarm and lower limit on rate-of-change alarm is determined by multiplying the scan interval by the number of times sampled. Where do you set the scan interval?
(ns-faq-dxadvanced-1108-setting)
To set the scan interval, press MENU (to switch to setting mode), hold down FUNC for 3 seconds (to switch to basic setting mode), and select the Menu tab > A/D, Memory. For details, see section 3.1, “Setting the Scan Interval and the Integra...
In the Partial Expanded Display settings, I enter "%" for the position. What are the values for 0% and 100%?
(ns-faq-dxadvanced-1115-setting)
0% and 100% are the lower and upper limits of span, which is the display range. The boundary value is the position on that range, expressed as a percentage, that divides the compressed and expanded display areas.
When I split the screen in 2, I can't display the current trend and historical trend at the same time. What should I do? I'm using event data.
(ns-faq-dxadvanced-1116-setting)
The procedure you mentioned can only show historical trends of display data. It won't work with event data.
I set temperature and pressure to a single group in the display group channel settings. How can I display the scales of both temperature and pressure?
(ns-faq-dxadvanced-1117-setting)
Under Setting menu > Measurement channel > Zone scale bar graph, you can set the scale position and number of divisions for each channel. Set the scale positions separately for temperature and pressure. If the scales of multiple channels are se...
What is the difference in the meaning of "Day" when selecting a report type of Day versus selecting (H+D)?
(ns-faq-dxadvanced-1118-spec)
When you select “Day,” the daily data from each day is added to the report files up to the previous day. In one month, the daily report file is completed. When you select H+D, a report file is created starting from the daily data of the r...
I entered the Tag No. keyword in a record template but the tag number doesn't make it into the Excel report file. What should I do?
(ns-faq-dxadvanced-1119-setting)
The keyword for tag no. is “ChId.” Please check the keyword again.
Can I omit parameters when using record template keywords?
(ns-faq-dxadvanced-1120-setting)
Parameters are written in the order: report type; report channel number; start date/time; and end date/time. The report type and channel number cannot be omitted, but you can omit the start and end date/time.
Can I add multiple record template keywords to a single cell? For example, could I put the channel number and tag comment in one cell?
(ns-faq-dxadvanced-1121-setting)
If there are multiple keywords in a single cell, only the first keyword is valid. In your case, you'll need to use separate cells.
I consulted the specifications for the "Cu10, Cu25 RTD Input/3 Leg Isolated RTD Input (/N1)," under input types, there are RTDs with no reference temperature indicated. How can I check their reference temperatures?
(ns-faq-dxadvanced-1122-spec)
See the following. Cu10 (GE): at 25°C Cu10 (L&N): at 25°C Cu10 (WEED): at 25°C Cu10 (BAILEY): at 0°C  
The tag number box does not appear so I can't input the tag number. What should I do? I was able to input tag comments.
(ns-faq-dxadvanced-1113-setting)
In Basic Setting mode, change the Tag No. Use/Not setting to Use. You can find the procedure in section 5.2, “Displaying Tags or Channel Numbers” of the user's manual (IM 04L41B01-01E). ...
Configured channel numbers and tag comments to display, but only the channel numbers appear on screen.
(ns-faq-dxadvanced-1114-setting)
Q: In Basic setting mode, I set the Tag No. Use/Not setting to Use, but I don't set the tag number string (I enter all spaces), and this is supposed to be the setup to display channel numbers and tag comments (referring to section 5.2, “Dis...
In appendix 1, "File Size of Display Data and Event Data" of the user's manual, there is a table, "Size of Information Other Than the Sampled Data." Does the size of message and alarm information ever change depending on the channel information?
(ns-faq-dxadvanced-1123-spec)
No, it only varies depending on the number of messages and alarms.
How can I check the MAC address on the DX1000/DX2000 series?
(ns-faq-dxadvanced-1124-setting)
You can find it in the system information screen or the network information screen. In the operation mode, press FUNC. The FUNC key menu appears. On the FUNC key menu, press the System info soft key or the Network info soft key. The MAC address ...
The error "code flash sum error" appears on screen, and the unit won't respond to user operations. What should I do?
(ns-faq-dxadvanced-1130-other)
The internal flash memory is experiencing an error. Contact your dealer or Yokogawa representative for repairs.
If I set the DX1000/DX2000 to High Speed mode, does the number of input channels decrease?
(ns-faq-dxadvanced-1132-spec)
No, even in High Speed mode, the number of input channels is the same as Normal mode. Note: In High Speed mode, the integral time of the A/D transformer is fixed at 600 Hz, and the power-line period noise rejection performance will be lowered. If mea...
When trying to receive settings from the recorder in the DAQSTANDARD hardware settings, the message, "E0401 Communication error" appears and receiving fails.What should I do?
(ns-faq-dxadvanced-1133-other)
Check the following items. Whether the LAN cable is correctly connected, and whether the PC's wireless LAN function is OFF. Whether the IP addresses of the recorder and PC are set. Whether you are using the latest version of DAQSTANDARD. In...
I selected Scale (linear scaling) for the DX1000/DX2000 input range mode. I'm trying to set the upper-limit value to 500 (500.0) but it doesn't let me set a value higher than 300 (300.0).
(ns-faq-dxadvanced-1135-setting)
In the DX1000/DX1000N/DX2000 range settings, the allowable setting range from lower limit to upper limit is -30000 to 30000 (excluding the decimal point). Change the upper or lower limit value or the decimal point to stay within that range. The decim...
Can channels be added to the DX1000/DX2000? For example, can I add channels to the DX1006 making it the DX1012, or to the DX2010 making it DX2020?
(ns-faq-dxadvanced-1136-spec)
With the DX1000/DX1000N/DX2000, you cannot add channels.
Can I use DAQSTANDARD on Windows 7?
(ns-faq-dxadvanced-1131-spec)
DAQSTANDARD supports Windows 7 version R8.22.01 or later. If you have an unsupported version, download and install the latest version. *Log-in Required For the license number, use the universal key. ...
Can I use DAQSTANDARD on Windows 10?
(ns-faq-dxadvanced-1134-soft)
Starting with version R9.03.06, DAQSTANDARD supports Windows 10. If you have an unsupported version, download and install the latest version. *Log-in Required During installation, use license number 116-00000-8807 when prompted. ...
I'm doing integral flow calculations on the DX1000/DX2000. I want to reset the integral flow every hour and every day, but how should I configure that?
(ns-faq-dxadvanced-1137-setting)
(1) As an example, enter the following formulas for calculating flow on MATH channel 1 and MATH channel 2. 101=TLOG.SUM(001) 102=TLOG.SUM(001) (2) MATH channel 1 resets hourly, and MATH channel 2 resets daily. To set the reset timing, select MENU ke...
How can I monitor the DX1000/DX2000 screen on a PC via the Internet?
(ns-faq-dxadvanced-1139-connect)
You can monitor the DX1000/DX1000N/DX2000 screen from Internet Explorer. Use the following steps. Set the IP address on the recorder and PC. In the recorder settings, under Basic Setting mode > Communication (Internet) > Server function, se...
How can I input a 4-20 mADC signal to the DX100/DX2000?
(ns-faq-dxadvanced-1140-spec)
Convert the signal to 1-5 VDC with the accessory 250 Ω shunt resistance (for M4 screw terminals, PN 415920)
I'm setting an upper-limit alarm for measuring temperature. Can I prevent the alarm from occurring when the temperature rises temporarily?
(ns-faq-dxadvanced-1138-setting)
Yes, set a delay upper-limit alarm. A delay upper-limit alarm will not engage until the measured value remains above a specified value for a specified length of time (the delay time).
I’m entering settings on the DAQSTANDARD (DXA120) hardware configurator software, but how do I input the °C unit?
(ns-faq-dxadvanced-1141-setting)
Enter "^C." The caret (^) symbol is on the "6" key. (Use only a single-byte character.)
Can I save the DX1000/DX2000 settings and then load them on an instrument of the same configuration with new firmware?
(ns-faq-dxadvanced-1143-setting)
Yes. When loading settings, the difference in version is ignored.
Can I load DX1000/DX2000 settings on an instrument with different suffix codes and numbers of channels?
(ns-faq-dxadvanced-1144-setting)
If the number of channels and suffix codes are different, you can load the settings that are common to both instruments. For example, if you load settings from a 10 ch model onto a 20 ch model, no settings are loaded for the 11th and higher channels,...
On a DX1000/DX2000 series with the remote suffix code /R1, can I start/stop recording using an external voltage level signal?
(ns-faq-dxadvanced-1145-setting)
Yes. Settings Set the input terminal mode to "DI," the range to "Level," the upper-limit alarm to "1," and the alarm output destination to "Internal switch." Set the relevant internal switch as an even...
If my DX1000/DX2000 series doesn’t have the remote suffix code /R1, can I start/stop recording externally?
(ns-faq-dxadvanced-1146-setting)
Yes, by writing values to the recorder’s register number 409503 (memory start/stop) using Modbus communication. For instructions on Modbus communication, see“Communication Interface User’s Manual.” ...
If a power failure occurs on the DX1000/DX2000 series while recording, is the data saved to the CF card?
(ns-faq-dxadvanced-1147-spec)
If Auto save is On (the default), data up to the moment just before the power failure is written to the CF card after power is restored.
If a power failure occurs on the DX1000/DX2000 series while recording, does recording continue after power is restored?
(ns-faq-dxadvanced-1148-spec)
Recording does not take place while the power is out, but it automatically restarts when power is restored. The data before and after the power failure are saved to separate files.
If a power failure occurs on the DX1000/DX2000 series while recording, and then recording restarts after the power is restored, can I combine the recorded before and after data files in the viewer?
(ns-faq-dxadvanced-1149-spec)
Yes. However, the region during the power failure appears blank.
When sending settings via communications on the DAQSTANDARD hardware configurator, can I prevent the IP address from being sent?
(ns-faq-dxadvanced-1150-soft)
Yes. In the DAQSTANDARD hardware configurator, on the menu bar, select Communication > Send. The IP address and other information is not sent. To send the IP address and other settings related to communication connections, select Communication >...
I’m measuring temperature, but the recorder's temperature display is higher than the actual temperature. Can I correct the temperature on the recorder? I don't have the broken line correction option (/CC1).
(ns-faq-dxadvanced-1151-setting)
Yes, by setting the range rating mode to Scale. For example, with a K thermocouple and measured values with an input span of 0.0°C–100.0°C, to lower all temperatures by 1°C, enter the following settings. Mode: Scale Range: TC ...
I registered users on the DX1000/DX2000 advanced security model (/AS1). What is the login password?
(ns-faq-dxadvanced-1152-setting)
The first time you log in, use the default password. You can find the default password on page 2-10, “2.2 Logging in and out” in user’s manual IM 04L41B01-05 EN for the advanced security function (/AS1). Note: That will be the defau...
I registered users on the DX1000/DX2000 (no /AS1). What is the login password?
(ns-faq-dxadvanced-1153-setting)
There is no default password. Leave the password field blank when you log in.
Can I make it so that alarms don't display when they occur?
(ns-faq-dxadvanced-1154-setting)
Yes. In Basic setting mode, turn ON the non-detection function for alarm operation. Next, turn OFF detection on each channel and each alarm.
If I adjust the time gradually, what happens to the saved data?
(ns-faq-dxadvanced-1155-spec)
The data being recorded is saved at the gradually adjusted time. The time of data that are already files are not corrected.
Which advanced security function (/AS1) models apply to which category classifications in the "Computerized system adequacy management guidelines at pharmaceutical and quasi-drug manufacturing and sales companies?"
(ns-faq-dxadvanced-1156-spec)
Category classifications differ depending on the suffix codes. If neither the MATH nor custom display are added, it's category 3. If either the MATH or the custom display are added, it’s category 5.
Waveforms of channels other than those from the group are displayed in the trend screen. How do I prevent waveforms not in the group from displaying?
(ns-faq-dxadvanced-1157-setting)
"Display all channels" may be selected in the trend screen display settings. Select "Group display." Instructions: DISP/ENTER > Trend > Group display
I forgot to order a calibration certificate at the time of purchase. Can I order it later?
(ns-faq-dxadvanced-1158-other)
Please contact your Yokogawa sales representative or dealer for information about ordering calibration certificates.
Can I record the max, min, and instantaneous values every minute?
(ns-faq-dxadvanced-1159-spec)
You can record 2 files, the display data and the event data. The display data records the max and min values, and the event data records the instantaneous values. However, this is not available with the advanced security option (/AS1) or Multibatch f...
When using RTD for the input, what is the measured current value?
(ns-faq-dxadvanced-1160-spec)
The measured current of RTD is 1 mA.
Can I change the display orientation (horizontal/vertical) of the trend waveform?
(ns-faq-dxadvanced-1161-setting)
Yes. Change the display orientation setting (horizontal/vertical), and then save it. See section 5.10, “Changing the screen layout, clear waveform on start setting, message display direction, waveform line width, and grid" in the user'...
I downloaded DAQSTANDARD software, but I don’t know what my license number is and I can’t install it.
(ns-faq-dxadvanced-1162-soft)
During installation, use license number 116-00000-8807.
I can't set a temperature range of 0.00–350.00 in the scaling. What is the allowable setting range for scaling?
(ns-faq-dx-3001-spec)
Omitting the decimal point, the values that can be set for scaling are -30000 to 30000. 350.00 exceeds the setting range, and can't be entered. In this case, set it to "0.0–350.0".
The display of the scale setting upper limit value just automatically goes back 2 decimal places.
(ns-faq-dx-3002-spec)
The decimal place is determined by the scale lower limit value setting. Set the decimal place in the scaling lower limit value.
What does the "/div" mean in the display update interval?
(ns-faq-dx-3003-term)
This means 1 scale division of the time axis on the trend screen.
What are the sizes of display and event data?
(ns-faq-dx-3006-spec)
Display data: Measured data: 4 B/data; computed data: 8 B/data Event data: Measured data: 2 B/data; computed data: 4 B/data
What is the difference between event data and display data?
(ns-faq-dx-3005-spec)
Event data are the instantaneous values recorded at each scan interval. Display data are the maximum and minimum sampled values recorded within the display update time. For details, see the following. Display and event data files ...
Why are there 2 data values (max and min) for acquired data?
(ns-faq-dx-3007-spec)
Because the data type is set to display data. Display data is saved as the maximum and minimum values measured in the scan interval within the sampling interval. For details, see the following. Display and event data files ...
Can I view past display data?
(ns-faq-dx-3015-spec)
Yes. Using the Historical function, you can view a historical display of data in internal memory or external media.
What is Event data?
(ns-faq-dx-3017-spec)
Event data are the instantaneous values recorded at each sampling interval. They can be recorded at faster intervals than display data, and can therefore are used for analysis in greater detail.
Can Event data also be viewed in the historical trend display?
(ns-faq-dx-3018-spec)
Yes.
Using display data, how can I change the data save interval?
(ns-faq-dx-3009-spec)
To change the save interval for display data, change the display update interval. Note that the unit of the display update interval is "/div," and 30 data are saved per div. Thus, for a display update interval of 30 min/div, the sampling in...
What is the display update interval for recording display data at 1 minute intervals?
(ns-faq-dx-3010-spec)
30 min/div. For details, see the following. Display and event data files
Why are there 1–4 alarms per channel?
(ns-faq-dx-3020-spec)
Four alarms (levels) can be set per channel. You can also set the same type of alarm for different levels.
Can I perform contact output on alarms?
(ns-faq-dx-3021-spec)
This requires the alarm output relay option (suffix code /Ax). Note that the number of contact outputs that can be added depends on the model.
If the alarm output relay option (suffix code /Ax) is installed, can multiple alarms be assigned to 1 alarm output?
(ns-faq-dx-3022-spec)
Yes. Note that you can set the alarm relay output to OR or AND. By default, all alarm output terminals are set to OR, and the relay outputs if any of the assigned alarms occurs.
Can I set alarms beyond the span setting range?
(ns-faq-dx-3023-setting)
No, the span or scaling range cannot be exceeded.
Is there a way to delay occurrence of alarms?
(ns-faq-dx-3024-spec)
Yes, there is an Alarm Delay function. The function activates the alarm when the alarm state continues for a specified time.
Is alarm information recorded to a file?
(ns-faq-dx-3025-spec)
Yes. You can view the list by using the DAQSTANDARD or other software.
What information is displayed in alarm summaries?
(ns-faq-dx-3027-spec)
The channel on which the alarm occurred, the time, and other information.
Can I receive email notification of alarm occurrences?
(ns-faq-dx-3028-spec)
Yes, with the email transmission function. When an alarm occurs, mail is sent to the specified email address.
What are the specifications for remote control contact input?
(ns-faq-dx-3029-spec)
They are non-voltage contact or open collector (TTL level, 5 V).
With the remote control option (suffix code /R1), through what kind of contact can I control recording start/stop?
(ns-faq-dx-3030-spec)
This is controlled based on the rising or falling edge of the remote signal. For contact input, the signal rises when the contact changes from opened to closed, and falls from closed to opened. For open collector, the collector signal rises on Hi &ra...
Can I write messages on the trend display using contact input?
(ns-faq-dx-3031-spec)
With the remote control option (suffix code /R1), you can write 8 messages by registering them on up to 8 contact inputs in advance.
Can I set the clock externally?
(ns-faq-dx-3032-spec)
Yes, with the remote control function. This function sets the internal clock to the nearest hour (works if the current time is within 2 minutes of the hour).
Are MATH channel values recorded?
(ns-faq-dx-3033-spec)
Yes. They are recorded just as with measured values.
Can I display MATH channel values in trends?
(ns-faq-dx-3034-spec)
Yes. You can display trends just as with measurement channels.
Does computation start/stop on individual channels, or on all channels at once?
(ns-faq-dx-3035-spec)
All channels at once. MATH reset also occurs on all channels.
If resetting TLOG.SUM with an internal timer, what is the longest timer interval?
(ns-faq-dx-3036-spec)
The longest is a 24-hour interval.
Can I reset integral values?
(ns-faq-dx-3039-spec)
If integrating with the TLOG calculation, you can reset it with the timer function.
Can I automatically transfer recorded data files using the FTP client function?
(ns-faq-dx-3042-connect)
This is possible if you connect a PC to the network via Ethernet and set up a PC as an FTP server. Then, set up a DX account on the FTP server so that the DX can access it. Leave the FTP server running all of the time.
What are the data types that can be sent via FTP?
(ns-faq-dx-3043-connect)
Display, event, and report data files can be sent.
With a DX as the FTP server, can I transfer data files saved on external memory media to a PC?
(ns-faq-dx-3045-connect)
Using FTP client software on the PC, you can transfer or delete files on external memory media. However, you cannot access the files in internal memory.
Can I easily monitor a DX's measured values on a PC without special software?
(ns-faq-dx-3046-spec)
Yes, by using the Web server display function. After connecting to the network via Ethernet, you can type the DX's URL into a web browser on the PC (Internet Explorer, etc.) and view the screen that is currently displayed on the DX in the web bro...
What is the screen update interval when monitoring screens on the web?
(ns-faq-dx-3047-spec)
The update interval of the web monitor page is approximately 30 seconds.
Can I switch the DX screen displayed on the web from the PC?
(ns-faq-dx-3048-spec)
From the web, you can access an operator page and a monitor page. On the operator page, you can switch screens from a web browser. You cannot switch screens on the monitor page.
If I view display data files from a PC using the DAQSTANDARD viewer trend screen, the trend display is filled in like a bar graph.
(ns-faq-dx-3050-soft)
Display data records the max and min values during the recording period. The trend screen shows a line connecting the max and min values at each point in time, making the trend display appear filled in like a bar graph.
In DAQSTANDARD viewer's statistical computation over an area, what do the max and min refer to?
(ns-faq-dx-3051-soft)
This assumes that the data type is display data. Display data records the max and min values during the recording interval, so those are the values it refers to.
On the DAQSTANDARD software that comes standard with the unit, can you monitor real time data via communication?
(ns-faq-dx-3052-soft)
DAQSTANDARD does not have a monitoring function. Please use DAQEXPLORER (sold separately).
How do I set the IP address of the DX?
(ns-faq-dx-3049-setting)
You set the IP address on the DX main unit.
Can I convert a DX series (DX100/DX200) settings file to a DXAdvanced series (DX1000/DX1000N/DX2000) settings file?
(ns-faq-dx-3059-soft)
Yes, by using the DX/DXAdvanced Setup File Conversion Tool. You can download it from our website. *Log-in Required
Can I get information on EU RoHS directive support?
(ns-faq-gxgp-046-other)
For instruments that support RoHS 10 restricted substances, see GS 04A01A01-02EN. For instruments that support RoHS 6 restricted substances, see GS 04A01A01-00EN. ...
Can you tell me where to download catalogs, specifications, user manuals, technical information, drawings, software, and CAD data?
(ns-faq-gxgp-097-other)
You can download these items from the Partner Portal member site *Log-in Required. You must register (free) to use Partner Portal.
Can I record integral value data?
(ns-faq-dx-3038-spec)
By adding the MATH option (suffix code /M1), you can use a TLOG-based integral function. Using this operator, you can record integral data of a certain time.

Материалы

Брошюры
Руководства по эксплуатации
Технические характеристики
Программное обеспечение
Техническая информация
Чертежи

Хотите узнать больше о наших технологиях и решениях?

Контакты
Наверх