Austria AT   
UT32A-D
Control Devices

UTAdvanced UT32A-D

Der UT32A-D ist ein kompakter Regler mit digitaler Anzeige und wählbarer 2-Schleifen-Regelung. Er bietet zusätzlich eine Ladder-Sequenzfunktion.

CSA C22.2 61010-/1
UL61010-1
Nach DIN schienenmontierte Regler sind in Kürze mit CE-Kennzeichnung erhältlich

Merkmale

Gehobene Regelfunktion

  • Ladder-Sequenzfunktion
  • Fuzzy-Logic-Regelung

Einfachheit

  • Einfach abzulesendes großes LCD-Farbdisplay mit 14 Segmenten
  • Textscroll-Funktion für Parameter
  • Navigationshilfe und Navigationstasten
  • Programmierbare Funktionstasten
  • Benutzerdefinierbare Standardwerte
  • Unterstützt mehrere Sprachen (Englisch, Spanisch, Französisch, Deutsch)
  • Kompakte Bauweise mit einer Tiefe von 65 mm

Netzwerkbetrieb

  • RS-485 (Modbus/RTU, Peer-to-Peer, koordiniert, PC-Link)

Zuverlässigkeit

  • 3 Jahre Garantie*1
  • RoHS/WEEE
  • NEMA4*2/IP66-Frontblende
    *1: Die 3-Jahres-Garantie gilt für 36 Monate nach Lieferung ab Werk.
    *2: Nur Hose-Down-Test Anwendung

Software

CSA C22.2 61010-/1
UL61010-1
Nach DIN schienenmontierte Regler sind in Kürze mit CE-Kennzeichnung erhältlich

Details

Publikationen

Applikations-beschreibungen
Easily Adding Messages to Manufacturing Data Using the Touch Panel
Thumbnail
Übersicht:

In the plants of food and beverage manufacturers, there are times when monitoring and recording of production equipment is necessary inside clean rooms. This is an introduction to monitoring and recording in clean rooms using paperless recorders.

Industrien:
I'm editing a CC-Link communication profile on the LL50A. I want to add the UT32A-D type to the RS485 communication line, but the PV2 register symbol doesn't appear.
(ns-faq-ut-2168-setting)
Select Modbus slave device UT32D.
Even when I turn ON the power, nothing appears on the UT display.
(ns-faq-ut-2013-setting)
The display is blank if you turn ON the power while a a dedicated LL50A cable is plugged into the maintenance port. Try removing the cable and restarting.
Can you tell me the procedure for assignment when the heater break alarm output option (suffix code /HA) is installed?
(ns-faq-ut-2015-setting)
Assignment settings are not necessary. The heater break alarm output has a dedicated output terminal.
I can't find a parameter I want to set.
(ns-faq-ut-2001-setting)
Please see the parameter map for your specific model. UTAdvanced Series Parameter Maps and Lists
I set up a difference lower limit alarm, but no alarm is output.
(ns-faq-ut-2017-setting)
In the case of the difference lower limit alarm, the alarm setting is a negative value. For example, you need to set it to "-5°C."
With the UTAdvanced ladder program function, can I use constants and other parameters in basic math functions?
(ns-faq-ut-2024-connect)
You can use the constant K and parameter P.
Are communications with the FA-M3 possible?
(ns-faq-ut-2021-connect)
Yes. Use a UT link module for the FA-M3, and use PC link communications (RS-485) for the temperature controller communication protocol selection.
Can I use an RS-485 communication program written for the GREEN series (UT300/UT400/UT500/UP300/UP500/UM300) on a UT-Advanced series instrument?
(ns-faq-ut-2025-connect)
Program changes for reading PV and OUT, writing SP, and other basic parameters are not necessary. There are registers and relays that support the GREEN series. For details see the UTAdvanced series communication interface (RS-485, Ethernet) user'...
When using the LL50A to create ladder programs, which ladder program edit mode should I use: "input ladder calculation," "output ladder calculation," or "user ladder"?
(ns-faq-ut-2030-program)
Generally you should create programs in "user ladder" mode. If needed, you can rewrite the input ladder and output ladder portions.
I'm creating ladder programs on the LL50A. I want to set input computed results to R.SP, but I see lots of digits are displayed after the decimal point of the data on the ladder monitor. Can I reduce the number of digits displayed after the decimal point?
(ns-faq-ut-2031-program)
The DATA register uses a 4-byte floating point number, therefore it displays a lot of digits. Try using the K or P registers, since they handle 2-byte integer data.
Can I use analog input in computations?
(ns-faq-ut-2032-program)
You can use it in ladder programs. On the UT55A, you can acquire up to 4 analog inputs.
Can I rewrite constants used in ladder programs via communication?
(ns-faq-ut-2033-program)
Variable parameters P01-P10 can be rewritten via communication. You'll need to use the variable parameters as constants.
Can I disable ladder programs that I used?
(ns-faq-ut-2034-setting)
On the LL50A, change the system data's ladder sequence function from USE to DON'T USE. If not using the LL50A, initialize the main unit.
Can I detect when the power is turned ON?
(ns-faq-ut-2035-program)
Yes. Use the PON flag on contact B.
My LL50A ladder program monitor does not start.
(ns-faq-ut-2036-program)
It won't start while the system data or parameter setting screen is displayed. Close those screens and restart.
A ladder program that I wrote doesn't work properly.
(ns-faq-ut-2037-program)
Check the operation of the program on the LL50A ladder program monitor.
My ladder program's comparison commands don't work properly.
(ns-faq-ut-2038-program)
The comparison commands of the digital indicating controllers (UT55A/UT52A/UT35A/UT32A) and program controllers (UP55A/UP35A) compare integers (rounded to the nearest decimal). If making comparisons that include decimals, first multiply the necessary...
When using contact input in ladder programs, is it necessary to turn OFF the contact function assigned to the setup parameters?
(ns-faq-ut-2039-program)
For contacts that have duplicated functions, it is necessary to turn them OFF on the setup parameter side.
Can you tell me how to wire and set up waste liquid pH control?
(ns-faq-ut-2041-setting)
Please see the document below. It is an example of wiring and settings for pH control using the Quick Setup function. Affected models: Standard UT52A/UT55A models (if there are 2 types of chemicals, select the heating/cooling model) Setup procedure,...
I'm controlling the temperature of an electric furnace using a thyristor. How should I wire and configure this?
(ns-faq-ut-2042-setting)
Please see the document below. It is an example of wiring and settings for controlling electric furnace temperature with a thyristor using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperature with...
I'm controlling the temperature of an electric furnace using solid state relays. How should I wire and configure this?
(ns-faq-ut-2043-setting)
Please see the document below. It is an example of wiring and settings for controlling electric furnace temperature with solid state relays using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperatu...
Can you tell me how to wire and set up flow control using an inverter?
(ns-faq-ut-2044-setting)
Please see the document below. It is an example of wiring and settings to control flow with inverters using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Flow with Inverters)" ...
I'm controlling tank level ON/OFF. How should I wire and configure this?
(ns-faq-ut-2045-setting)
Please see the document below. It is an example of wiring and settings for tank level ON/OFF control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Level ON-OFF)" ...
I'm doing proportional control of tank level. How should I wire and configure this?
(ns-faq-ut-2046-setting)
Please see the document below. It is an example of wiring and settings for tank level proportional control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Level Proportion)" ...
I'm controlling tank pressure. How should I wire and configure this?
(ns-faq-ut-2047-setting)
Please see the document below. It is an example of wiring and settings for tank pressure control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Pressure)" ...
With the LL50A and UTAdvanced, can I perform RS-485 communications without a dedicated cable?
(ns-faq-ut-2051-connect)
Yes, if using a UTAdvanced series instrument with the RS-485 communication option. Set the RS-485 protocol on the main unit to 8 (MBRTU: Modbus RTU). The initial value is 8. Select RS-485 in the LL50A communication execution screen, and make the comm...
How can I display parameters that aren't displayed in the LL50A parameter setting software?
(ns-faq-ut-2052-soft)
If the LL50A's display setting is not PRO, some parameters won't display. Change the LL50A's display parameter as follows: Display > Parameter > Display level > Professional. The LL50A's display level must be set separately f...
Can I acquire trend data on the LL50A?
(ns-faq-ut-2053-soft)
You can display and acquire PV, SP, and OUT values as trend data. The trend data you acquire can be saved as a CSV file.
Can I switch scaling using contact input?
(ns-faq-ut-2054-program)
Yes. Use the SCAL ladder program command.
What is the resolution of control output (4–20 mADC)?
(ns-faq-ut-2055-spec)
It is 1/20000. That is equivalent to approximately 14.5 bits.
I'm controlling tank temperature. How should I wire and configure this?
(ns-faq-ut-2048-setting)
Please see the document below. It is an example of wiring and settings for tank temperature control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Temperature)" ...
I'm controlling furnace temperature with a motorized valve. How should I wire and configure this?
(ns-faq-ut-2049-setting)
Please see the document below. It is an example of wiring and settings for controlling furnace temperature with a motorized valve using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperature with a ...
I'm controlling temperature with a heat exchanger. How should I wire and configure this?
(ns-faq-ut-2050-setting)
Please see the document below. It is an example of wiring and settings for controlling heat exchanger temperature using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Heat Exchange Temperature)" ...
To cause setpoints (SP) to change at a fixed rate, I set the SP ramp up and down parameters (UPR and DNR). Is this function still enabled when changing the SP value through remote input (RSP)?
(ns-faq-ut-2058-spec)
Yes. The SP ramp up (UPR)/SP ramp down (DNR) function supports changing the SP value with the UT55A front panel buttons or remotely.
Are all COM terminals for contact input connected internally?
(ns-faq-ut-2061-spec)
Yes.
Is there an easy way to change the settings for alarms 1 and 2?
(ns-faq-ut-2062-spec)
If you register the A1 and A2 parameters (for setting alarms 1 and 2) to the select screen, you can display the alarm 1 and 2 settings simply by pressing the DISPLAY key repeatedly. Set the CS1 and CS2 select screen parameters to "2504" and...
Can I reverse the 4–20 mA control output and change to a 20–4 mA signal?
(ns-faq-ut-2063-spec)
Yes, the output signal can be reversed. In the setup parameter OUT menu, set the OU.A parameter to "20–4."
How can I enter initial settings?
(ns-faq-ut-2064-setting)
Please see an operation guide. Controller operation guides are available for standard and detailed models. (Ex.: UT55A-000-01-00 is a standard model, and UT55A-NNN-01-AN is an detailed model). Note that you can refer to the user's manual for any ...
OVER was displayed on the PV (measured value) display. How will the control output operate in this case?
(ns-faq-ut-2070-spec)
If OVER is displayed, the PV value will be 105% of the measurement range. The control output will be the result that is calculated using this PV value. On a -OVER, the PV value is calculated as -5% of the measurement range.
I initialized the controller, but no control output value is output.
(ns-faq-ut-2074-setting)
The controller's operation may be set to START/MAN. Check the controller operation indicator on the front panel.
B.OUT was displayed on the PV (measured value) display. What could be the cause of this?
(ns-faq-ut-2077-connect)
There might be breakage in a line. Check input wiring and sensors.If the input is restored, B.OUT will be cleared automatically.
There are differences between PV display values and the displays of other measuring instruments. Can I correct these?
(ns-faq-ut-2078-spec)
Yes, by using PV input bias (parameter BS).
An error occurs with position-proportional type automatic valve position adjustment (V.AT).
(ns-faq-ut-2083-setting)
(1) Check the wiring: In MAN mode, set OUT display. Use the UP and DOWN keys to confirm operation of the control valve, and that the OUT value changes. The UP key operates the normal rotation side relay, and the DOWN key operates the reverse rotation...
Is a terminal cover included?
(ns-faq-ut-2088-select)
The UT52A, UT55A, UP55A, and UT75A come standard with terminal covers. For the UT32A, UT35A, UP35A, UP32A, and UM33A, specify the /CV option when order on or after May 31, 2015. They are also sold separately. Models: UTAP001UT75A, UT55A, UT35A, UP55A...
Can I set the PV display to -100 with 20 mA input, and to 0 with 4 mA input?
(ns-faq-ut-2089-setting)
In this case, 20 mA is the minimum value of PV input, and 4 mA is the maximum. In the setup parameter PV menu, set RH=4.00 and RL=20.00 (the input range maximum and minimum values). For the PV input scale max, min, and decimal place, set SH=0, SL=-10...
Can I switch the temperature units between°C and °F?
(ns-faq-ut-2087-spec)
Per the metering law, in Japan you can only use °C. For customers who require overseas-specification products that can display Fahrenheit for embedding in a device exported outside of Japan, please contact your dealer or Yokogawa representative. ...
I'm trying to switch the PID number with DI input but it's not working correctly. To check, I'm looking at the green numbers in the upper left of the SP display.
(ns-faq-ut-2090-spec)
The green numbers in the upper left part of the SP display are the SP numbers. If you register PID numbers in the select screen, you can display them in the SP display area (in orange). Register PIDN_L1_1 under Setup parameters > CSEL > CS1. ...
Do you have a 48 x 96 sized controller that supports CC-Link?
(ns-faq-ut-2091-select)
We have the UT52A/UT32A/UP32A in the UTAdvanced series. For an indicator with alarms, we have the 96 x 48 sized UM33A.
I perform auto-tuning on the UT, but the auto-tuning parameters (AT) do not appear.
(ns-faq-ut-2094-setting)
Check the following. Is the control type (CNT) ON/OFF, or 2 position 2 stage control?--> If so, change it to something other than that. Is the STOP lamp lit? --> Start operation (RUN). Is the MAN lamp lit? --> Set it to AUTO.   ...
I purchased a UT with the communication function, but currently I'm not using the communication function. I haven't even wired communication, but the blinking SP decimal point of a communication error appears. Why is that?
(ns-faq-ut-2096-connect)
Check the operation mode and communication protocol. If the operation mode is Remote (REM lights) and it's set to coordinated (PSL=CO-S), an error will occur if there is no wiring.
Up to how many SSRs can be connected to the UT?
(ns-faq-ut-2097-spec)
The UT's voltage pulse specifications are: ON voltage 12 VDC or more; load resistance 600 Ω or more; ON voltage 0.1 VDC or less. For example, in the case of the Omron G3PH (operating voltage DC4-30 V, input current 5 mA or less), up to 4 un...
I'm perform auto-tuning on the UT. At about how much relative to the set point does the output switch?
(ns-faq-ut-2099-spec)
You can switch the output at about ±0.25% of the input range relative to the set point.
I want to check the currently used PID settings.
(ns-faq-ut-2102-setting)
At the time of shipment from the factory, the PID display is assigned to the Fn key on the UT front panel. If you press the Fn key, the currently used P (proportional band) is displayed. You can press the DOWN arrow key to check other items.
I'm doing temperature control. I did PID tuning, but the overshoots are still large and I want to suppress them. Is there a good way to do this?
(ns-faq-ut-2104-setting)
Try the overshoot suppression function (super function). Turn on SC: Operation parameter > TUNE > SC
I'm replacing my GREEN series with the UTAdvanced series. Is there anything I need to be careful of in terms of wiring?
(ns-faq-ut-2108-connect)
The common for all GREEN series alarm relay outputs are shared. In the UTAdvanced series, each alarm relay output has its own common. If used the same way, use external wiring to connect common to common.
If I switch the SP number will the PID number switch too?
(ns-faq-ut-2109-spec)
By factory default settings, the PID number is linked to the SP number. You can change the setting with the zone PID selection parameter (setup parameter CTL > ZON).
Does the alarm function work when operation is stopped (STOP)?
(ns-faq-ut-2110-spec)
By factory default setting, the alarm function still works when operation is stopped (STOP). You can change the setting by using the alarm mode parameter (operation parameter ALRM > AMD).
What is the alarm standby function?
(ns-faq-ut-2111-spec)
Standby means that even when an alarm condition occurs it is ignored and the alarm stays off until the alarm condition ends. When the signal enters a non-alarm region, standby mode ends. Standby works in the following situation. When powering on ...
Are the control and alarm hysteresis values set as percentages?
(ns-faq-ut-2113-setting)
They are set with the same industrial quantities as the input units.
I'm using the UP35A and UP55A. Are PV and local event hysteresis values set with percentages?
(ns-faq-ut-2114-setting)
Yes, as a percentage of the PV input range span or output span.
How can I check the RS485 communication status?
(ns-faq-ut-2116-connect)
For communication errors, the left side decimal point of the symbol display on the main unit blinks. If the SD or RD indicators light on upstream devices, check whether both are blinking.
I want to set the PID, output limiter, and hysteresis for each SP number.
(ns-faq-ut-2120-setting)
You can specify PID parameter groups for each SP number. Each PID parameter group includes PID, output limiter, hysteresis, and other items.
What is the minimum hold time that contact input can detect?
(ns-faq-ut-2121-spec)
For controllers, the status detection minimum hold time is the control interval + 50 ms. Also, for indicating alarms, it's the input sampling interval + 50 ms.
Why are PID parameters set with relay output?
(ns-faq-ut-2123-spec)
It's time proportional PID. That means that in addition to relay output, it can support TRIAC and voltage output. With time proportional output, control calculation result is output using the pulse width of an ON/OFF signal proportional to time. ...
Does the UTAdvanced series support CCC and GB standards? Can it be used in China?
(ns-faq-ut-2124-spec)
The UTAdvanced series is not a CCC standard scope. Since it has acquired the GB standard, it can be used in China.
Can the alarm operation be disabled during operation stop (STOP) or manual operation (MAN)?
(ns-faq-ut-2129-setting)
You can do this with the AMD alarm mode settings (within the ALRM operation parameter). 0: Alarm always active 1: Alarm not active during operation stop 2: Alarm not active during operation stop or manual operation
I want to stop the lamp indicator or action for unused alarms.
(ns-faq-ut-2136-setting)
Set alarm types AL1–4 or 8 (ALRM operation parameter) to 0.0.0.00.
Can I assign heater disconnection alarm 1 to alarm 1 output (terminal no. 108-109)?
(ns-faq-ut-2137-setting)
Yes, set parameter AL1.S (AL1 function select) to 4529.
Is there a limit on the number of times you can write to the D register via communication?
(ns-faq-ut-2140-spec)
No, there is no limit.
What should I do if DI input is not accepted on relay contacts?
(ns-faq-ut-2141-spec)
Use a relay that supports miniscule currents. The minimum ON current of a contact input (DI) is approximately 1 mA.
Can I remove the output limit value restriction during manual operation?
(ns-faq-ut-2143-setting)
By turning the OLMT output limiter switch OFF, the output limiter is disabled during manual operation.
When I start operation (RUN), control output doesn't change.
(ns-faq-ut-2144-setting)
Check whether the MAN lamp is lit. If it is, control output will not change. Press the A/M key to switch to AUTO.
When I change from STOP to RUN the control output overshoot becomes large. What can I do about that? There is no problem with PID tuning.
(ns-faq-ut-2145-setting)
Try the PV tracking function (PVT=ON). This function is useful for preventing sudden changes in the PV value. When operation starts, the PVT starts by matching SP to PV, and then uses an SP slope function (TMU, UPR, DNR) to gradually return SP to the...
I'm controlling temperature by using voltage pulse output to operate a heater with an SSR, but I can't stop the hunting. I already performed auto-tuning.
(ns-faq-ut-2146-setting)
Check the cycle time (CT) setting. For voltage output, try a cycle time setting of around 1 to 5 seconds.
Valve calibration parameters don't appear on position proportional controllers.
(ns-faq-ut-2147-setting)
It appears when the controller's operation mode is RUN and MAN.
I am connecting the UT and Mitsubishi's touch panel GOT using RS-485 communication. Which communication protocol should I choose?
(ns-faq-ut-2152-setting)
Choose PC link communication (sum check enabled or none). Please also refer to the Mitsubishi Touch Panel GOT catalog and user's manual.
I'm controlling pressure. Are there PID reference values?
(ns-faq-ut-2153-setting)
Perform tuning with these reference values: P=150 to 200, I=10 to 20, D=OFF.
I'm controlling flow. Are there PID reference values?
(ns-faq-ut-2154-setting)
Perform tuning with these reference values: P=150 to 200, I=10 to 20, D=OFF.
I'm controlling flue levels. Are there PID reference values?
(ns-faq-ut-2155-setting)
Try proportional control. Perform tuning with these reference values: P=10%, I=OFF.D=OFF, MR=0%.
With 1-5 VDC input, can I make the PV display 0.00 to -10.00 kPa?
(ns-faq-ut-2156-setting)
Yes. Set the following: IN=1-5V, RH=1.000, RL=5.000, SDP=2, SH=0.00, SL=-10.00.
I just purchased the UT and UM and the EV lamp turned ON. What does that mean?
(ns-faq-ut-2157-setting)
Per factory parameter settings, the EV lamp on the UT and UM is assigned to alarms, and may light depending on the measured input (PV) and setting values. Configure your EV lamp and alarm type settings to match your operating conditions.
I want to create a ladder program that writes output tracking values via communication.
(ns-faq-ut-2158-setting)
In your ladder program, use variable register P01 and others, and write the P01 value via communication. Then do a MOV of the P01 data to the tracking input value (TRK_CTL).
I'm using a thermocouple for the input, but "b.out" appears on the PV display. What should I check first?
(ns-faq-ut-2160-other)
“b.out” on the PV display indicates a break in the input. Check whether the signal from the sensor is getting through. Also, to narrow down the cause, you can short the input terminal of the UT itself, then if the UT's input is normal...
Can you tell me the inrush current value of the UTA series of instrument power?
(ns-faq-ut-2162-spec)
At DC24 V: Approximately 17 A, 1.5 ms At AC100 V: Approximately 4.5 A, 3 ms At AC240 V: Approximately 11 A, 3 ms
Can you tell me how to get the measurement accuracy when measuring 0 to 1000°C with a type K thermocouple? I selected input type K2 (-270.0 to 1000.0).
(ns-faq-ut-2163-spec)
Per the specifications, the accuracy of type K at 0°C or higher is ±0.1% ±1 digit. The measuring range in this case is that of the selected input type, -270.0 to 1000.0. You can calculate the accuracy as follows. ±0.1% of 127...
I purchased a DIN rail mount UTAdvanced series, but how should I configure it?
(ns-faq-ut-2165-spec)
Use the LL50A Parameter Setting Software, sold separately.
What is the measured current during RTD input?
(ns-faq-ut-2167-spec)
It is approximately 0.16 mA.
I'm pressing SET/ENTER on the front panel keys but I can't change the SP value.
(ns-faq-ut-2171-setting)
Check the key lock. If you see the R.SP display, in Remote mode (REM), that means SP is being set by an external (upstream, etc.) device and cannot be changed.
I want to add 10-segment linearizers to the UT control output value. Can the broken line output result be read via communication?
(ns-faq-ut-2176-spec)
Yes. The read registers will be control output D7621 (OUT_OUT) and transmission output D7624 (OUT_RET). Note that these registers are for data -1500 to 31500 (equivalent to -5.0% to 105%).
I set the UTA output to 10-segment linearizer approximation. Can the resulting output values be read via communication?
(ns-faq-ut-2177-spec)
Yes. The data will be -1500–31500. For the OUT terminal output, D7621(OUT_OUT) For the RET terminal output, D7624(RET_RET) For the OUT2 terminal output, D7623(OUT_OUT2L)  
Can I use square root extraction on measured input?
(ns-faq-ut-2183-spec)
Yes, by using a ladder program function. Use the square root command (SQR).Note that you can't set a low signal cutoff point. To use the ladder function, you will need the LL50A parameter setting software.
Can I make it display the alarm type when an alarm occurs?
(ns-faq-ut-2184-spec)
Yes, by using the message function. This function assigns messages that have been registered in advance to the PV value display section, and displays them based on contact input ON/OFF states. Setting example: MG1 = 4353
What is the MR (manual reset) function?
(ns-faq-ut-2185-spec)
This function operates during P and PD control (when integral time I = OFF). The manual reset value is the output value when PV=SP.
How to connect one UT with CC-Link communication to another downstream UT via RS485. The RS485 communication terminal of the UT with CC-Link communication is a 2-wire system, and that of the other UT is a 4-wire system.
(ns-faq-ut-2187-connect)
Q: I'm connecting a UT with CC-Link communication to another downstream UT via RS485 communication (Modbus master function). However, the RS485 communication terminal of the UT with CC-Link communication is a 2-wire system, and that of the other ...
I want to control the temperature of 3 zones. How should I configure it?
(ns-faq-ut-2191-select)
Make the UP the parent station of two UT child stations and run the coordinated communication.
I purchased a general type of controller. Can this control cooling?
(ns-faq-ut-2194-other)
Yes. Set the DR (direct/reverse operation switching) parameter of the PID item to DIR (direct operation).
I want to check the suffix code but I can't see the name plate. Is there another way to check it?
(ns-faq-ut-2195-setting)
When you turn ON the power, it shows up on the self-diagnostic screen that appears for a few seconds. The 3-digit number in the SP display section is the basic suffix code. (Ex.) For the UT55A-210-01-00, the number "210" appears. ...
After converting the controller manual output value to a number like the SP, can I finalize it with the ENT key?
(ns-faq-ut-2196-setting)
You can do this with the SET/ENT key system. Set MAN.T to ST.ET.
I'm using the Pt100 sensor. The PV input type IN parameters include PT1, PT2, and PT3, but which should I select?
(ns-faq-ut-2197-setting)
Select the type that is closest to the temperature range span that you are using.
Can I apply a 24 VDC voltage to a contact input?
(ns-faq-ut-2198-spec)
You cannot apply an external voltage. You can connect either a no-voltage contact or a transistor contact.
I want to output the results of calculations by ladder programs with 4-20 mA on the OUT output terminal, but nothing happens.
(ns-faq-ut-2207-program)
For analog output of calculated results to the OUT terminal, set the output selection type OT to 00.00 and the transmission output type 01RS to OUT1.
I want to output the results of calculations by ladder programs with 4-20 mA on the RET output terminal, but nothing happens.
(ns-faq-ut-2208-program)
For analog output of calculated results to the RET terminal, set the transmission output type RTS to OUT1.
I want to output the results of calculations by ladder programs with 4-20 mA on the OUT2 output terminal, but nothing happens.
(ns-faq-ut-2209-program)
For analog output of calculated results to the OUT2 terminal, set the first two digits of the output selection type OT to 00, and the transmission output type 02RS to OUT1.
Is the SP slope valid for remote SP values as well?
(ns-faq-ut-2210-spec)
Yes.
I want to contol pressure and temperature with a single pattern using the UP and UT.
(ns-faq-ut-2213-spec)
You can do this with the pattern 2 transmission function. With the program pattern 2 transmission function, you can create and transmit program patterns at the same time, aside from program patterns used in control.
When installing the UTAdvanced series, what is the depth in millimeters from the surface of the panel?
(ns-faq-ut-2214-spec)
65 mm. For details, see the specifications of individual models.
Can I use DO to transmit the SP number currently used on the UT to an external device?
(ns-faq-ut-2215-setting)
Yes. Assign an I relay to the DO parameter.
Can I switch heating and cooling control?
(ns-faq-ut-2218-spec)
Yes, by using PID switching. Generally, you set heating control to reverse action and cooling control to direct action.
Can I connect multiple instruments such as power controllers to a controller's analog current output?
(ns-faq-ut-2219-connect)
Yes, as long as the total input and wiring resistance of the connected instruments is 600 Ω or less.
I’ve coordinated operation between 2 UT's via RS485 communication. I want to compensate the SP value of the child UT but is that possible?
(ns-faq-ut-2224-setting)
Yes. Set remote ratio (RT) or remote input bias (RBS).
I wrote the alarm setting values from the UT350 to the UT35A via communication. On the UT350, the alarm setting values were common from 1SP through 4SP, but when updating to the UT35A, what should I do?
(ns-faq-ut-2231-spec)
Use the GREEN compatible registers DO231 (alarm 1 setting) through DO233 (alarm 3 setting). Ex.) DO231: A1_G (setting value of alarm 1 for GREEN) Write the values written to A1_G to A1_L1_1 through A1_L1_4. A1_L1_1(D2504) A1_L1_2(D2524) A1_L1_3...
Do you sell terminal covers?
(ns-faq-ut-2233-other)
Yes. Model: UTAP001 Supports: UT75A, UT55A, UT35A, UP55A, UT35A Model: UTAP002 Supports: UT52A, UT32A, UP32A, UM33A
To prevent mis-operation, is there a setting where you hold down the A/M button to switch the operation?
(ns-faq-ut-2240-setting)
Not with parameter settings, but you can do this with a ladder program.
Can I set it for 1 shot-only event display and contact output ON when an alarm activates?
(ns-faq-ut-2241-setting)
Not with parameter settings, but you can do this with a ladder program.
Is it possible to connect multiple contact inputs to a single relay contact?
(ns-faq-ut-2243-connect)
No, use 1 contact per input. If you connect multiple inputs, when you turn OFF the UT, the impedance lowers and mis-operation can result.
Can I choose the color of the UTAdvanced terminal cover?
(ns-faq-ut-2246-spec)
No, it only comes in white.
Is the current transformer for heater current measurement that is used by UTAdvanced made by Yokogawa Electric?
(ns-faq-ut-2247-other)
It’s from U-RD. Please purchase them from our dealers.
What is the model of the current transformer for heater current measurement used by UTAdvanced?
(ns-faq-ut-2248-spec)
Recommended CT:U-RD CTL-6-S-H: CT ratio 800, measurable current range: 0.1-80.0 Arms CTL-12L-30: CT ratio 3000, measurable current range: 0.1-180.0 Arms
How can I display the currently used PID no. on the operation screen?
(ns-faq-ut-2249-setting)
Turn OFF the U.PID parameter symbol in the setup parameter KLOC menu.
Can I set control for power fail recovery to MAN?
(ns-faq-ut-2117-setting)
For a power failure of approximately 5 seconds or more, you can do this with the restart mode R.MD setting. For power failures of less than approximately 5 seconds, the control operation prior to the power failure continues. ...

Downloads

Bulletins
Bedienungsanleitungen
Datenblätter
Software
Zeichnungen

Möchten Sie weitere Informationen über unsere Mitarbeiter, Technologien und Lösungen?

Kontakt
Top